touring bar made by POSH for W800 was not yet ready for production As an alternative to bar
I tried this one, which is close in dimension
A little more than NORMAL and 4mm higher than the Handlebar1 pc before the Touring bar The state of the system will be the same as it was before
Also Quantity:Pair (for Left and Right) The width is slightly narrower at 1cm each
The height of the Handlebar is just right for my short stature when I reach for it, and the width is a little It's so narrow that it's easy to relax around the shoulders without the extra tension in my shoulders
The switch holes are not aligned with the ZEPHYR1100, so you have to open them separately Mm
It would have been great if the surface finish was a little nicer, but the condition of the plating was not so good so
I lost a few stars
But from a cosmetic standpoint, it's great!
28.14 ~ USD (4,180 JPY)
Delivery Information
-
Please select product form first.
Product detail
Type: EZ-FIT
Material: Aluminum
Processing: Switch hole machined
Amount of movement: 7mm UP/8mm BACK
Outer Diameter: Φ22.2
Inner diameter: Φ14.0
dimension
・Vertical stock ratio: 7
・Front to rear stock ratio: 8
・Width: 690
・Height: 71
・Pull: 129
・Aperture angle: 28
・Standing angle: 73
**The bar ends are not included in the product.Separately for inner diameter 14Φ (Recommended: EFFEX Handlebar Weights / *W650 excluded) handlebar ends are required.(Stock bar ends cannot be used.)
*Depending on the model, it may be necessary to change the minimum cable routing.
*The cables may need to be replaced separately.
*Some models may not have a switch hole.
*There may be changes in product specifications due to the manufacturer's reasons..
* The image is only for reference. The image shown may differ from the actual product.
Specially designed for models with a comfortable position by moving it forward about 10mm compared to the normal position.
The design is based on the stock handlebar shape, but the grip part has been shifted in parallel.
The angle is the same as the stock one, so you can form a good riding position without damaging the image.
■No need to replace cables
It is designed for exclusive use of the model, so you don't have to worry about compatibility.
■Switch hole pre-machined
You no longer need to worry about positioning and preparing tools, and you no longer need to spend extra money.
■Shift the lever holder to the left or right
The mounting straight line is designed to be about 5mm longer.
The grip position of the lever can be fine-tuned.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
MODEL PAGE LINKS
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Customer Reviews
Reviews with image
Fits:KAWASAKI ZEPHYR1100 92-07
Apr 5, 2020
This is a very good position for use with the W800
Fits:KAWASAKI ZEPHYR1100 92-07
Apr 4, 2020
touring bar made by POSH for W800 was not yet ready for production As an alternative to bar
I tried this one, which is close in dimension
A little more than NORMAL and 4mm higher than the Handlebar1 pc before the Touring bar The state of the system will be the same as it was before
Also Quantity:Pair (for Left and Right) The width is slightly narrower at 1cm each
The height of the Handlebar is just right for my short stature when I reach for it, and the width is a little It's so narrow that it's easy to relax around the shoulders without the extra tension in my shoulders
It would have been great if the surface finish was a little nicer, but the condition of the plating was not so good so
I lost a few stars
But from a cosmetic standpoint, it's great!
Fits:KAWASAKI ZEPHYR1100 92-07
Dec 23, 2016
It became the Riding Positive shot as you wanted
I did not have the EZ - FIT Bar for Zr 7, I removed the OEM Hand Bar and measured and found the closest Handlebar and got to this Handlebar. Aperture, Height etc. It is a change of less than 1 cm but it became a very easy Riding position for me.
View DetailFits:HONDA CB1300 SF 03-09 (SC54), HONDA CB1300SUPER BOLDOR 05-09 (SC54)
Installed on: HONDA CB1300SB (Super Bol D'or, CB1300S)
Apr 2, 2024
I ordered these bars hoping they would be a good fit and upgrade for my cb13 I was not disappointed,they look great with the handlebar brace I have already and on the plus side the holes for the standard switches are already drilled out which makes these an easy going job to change
View DetailJul 31, 2022
It is safe because it is a car model Exclusive Design.
Replaced OEMHandlebar that was bent in a fall.
Since it is a car model Exclusive Design, it is also safe for Cable and other handling.
New Custom Articles
