With the old Takekawa speed sensor, the OEM discMounting bolt on the rear was restricted, the parts around the rear axle increased, and there was a demerit that the service coupler was always used.
It is supposed to be simple, using the application to convert the signal from the OEMSensor and send out a signal that matches the current situation, so wiring is also simple, just interrupting the two OEMCouplers.
The body also fits inside the small side cover, but the direction of the sensor is specified to prevent water intrusion, so be careful when fixing it.
I cured it with insulating tape just in case, and fixed it as specified.
It is difficult to say, but I have the impression that it would have been better if they had taken care of the Waterproof.
126.57 USD (18,803 JPY)
Delivery Information
No Information acquired.
FITMENT
-
SUPER CUBC125
(JA48-1000001 and later)
-
MSX125SF
-
MONKEY125
(JB02-1000001 or later)
-
GROM
(JC61-1000001 or later)
See all
HONDA
Product detail
**Equipment and environment required for installation
・To use the speedometer controller, you will need a smartphone or tablet that meets the requirements for using a speedometer controller.
・If you are not prepared for the environment, you cannot use this product.Also, you need to be connected to the Internet to download the application.
・You have to pay for the app.
*Speed Meter Controller Operating Environment
・Smartphones (iOS / Andoroid only)
・PC (Windows) cannot be used.
・iPhone 4s or earlier and iPad 3rd generation or earlier do not support Bluetooth LE, so they cannot be connected even if the OS has been upgraded.
・To install the SP TAKEGAWA application TST-CON [TAKEGAWA setting tool] (paid), you need to be connected to the Internet.
*About the parts that cannot be used together
・Please do not install aftermarket H. I. D. kits or LED lamps (fog / headlight) at the same time as the ballast / inverter (voltage conversion device), as most of them emit high voltage noise that adversely affects the digital circuit, causing product failure or malfunction.
・Please do not use the ignition device (ignition coil and plug cord) of the outside article because it becomes a cause of the malfunction and the product failure by the increase of the radiation noise accompanying the increase of the ignition voltage.
・It is possible to use with SP Takekawa Hyper Ignition Coil at the same time.Please do not use the aftermarket power generator because it may cause failure due to insufficient power generation or difference in voltage waveform.
・This product is not waterproof or drip-proof.If the unit is exposed to rain or water, there is a possibility that water will enter the unit and cause it to malfunction.
*This product cannot be installed on frames other than those listed in the "Compatible Models" section.
*When you change the tire brand or size from the original one, please input the outside diameter size or the measurement value which is described by the tire manufacturer.
*You can increase or decrease the displayed speed, but if you set it improperly, it may cause you to be cited for overspeeding.Use on public roads at your own risk.
*No refunds will be given for accidental app purchases.
*Do not operate or look at your smartphone / tablet device while riding.You are subject to a traffic violation.
*There may be changes in product specifications due to the manufacturer's reasons.
*Depending on the lot, the product may be delivered with the old price and label with the old JAN code before the price change..
This product corrects the deviation of the speed display when the tire brand or tire size is changed, or when the sprocket is changed, and can display the speed accurately.
It can be installed on the vehicle by coupler-on without any wiring work because it comes with a harness for the vehicle.
All settings are made using a smartphone or tablet, and the number of sprocket teeth and tire diameter are entered numerically.
Since the smartphone or tablet is connected to this unit via Bluetooth communication, there is no need to remove the exterior every time you want to change the settings.
■Speed Meter Controller Operating Environment
・iOS: iOS11 and above
To install SP Takegawa app and purchase model data, you need to connect to AppStore.
After installing SP TAKEGAWA application TST-CON [TAKEGAWA setting tool], please use the dedicated tool in the application.
・Andoroid Andoroid terminal Built-in Bluetooth version 6.0 or higher
To install SP Takegawa app and purchase model data, you need to connect to Google play.
Please install SP TAKEGAWA application TST-CON [TAKEGAWA setting tool] (paid) and use the dedicated tool in the application.
■Display of speed and error correction after gear change / without gear change
・Current speed (after gear change)
Corrected speed display (current speed) when front sprocket (drive sprocket), rear sprocket (drive sprocket), rear tire outer diameter (tire diameter) (mm), and sensor gear tooth number are changed from the stock value (stock specification) and set.
・Speed (unmodified)
Input of stock value (front / rear sprocket / rear tire outer diameter (mm) / sensor gear tooth number) The speed of the stock value is displayed.
This is the speed at which nothing has been modified.(You can see the speed after changing the parts and before changing the parts.)
・Stock speedometer error correction
The stock speedometer will display a higher speed than the actual speed.Therefore, if you use a non-stock measuring instrument such as GPS, the speed display will be different from the stock speedometer.
By installing this product, the error of the speed display can be corrected and the actual speed display becomes possible.
For vehicles with ABS, the correction range is limited.If the specified correction range is exceeded, the ABS error code will be displayed.
Please refer to the instruction manual for the setting.
■Display of maximum speed and 0-60 Km / h time measurement
・Maximum speed)
0Km/h to 300Km/h can be measured, and the maximum speed is updated every time and displayed on a smartphone or tablet device.
The maximum speed will be reset when you disconnect the application (key OFF) and reconnect.
If you want to save the record, please use the screenshot of your smart phone or tablet device.
・0-60km / h time measurement (*Please observe the legal speed limit.)
Measuring the time from 0 to 60km/h can be done.
Automatic measurement when you start riding.(Measurement is possible up to 100 minutes)
The 0-60Km/h time will be reset when you disconnect and reconnect the app.
If you want to save the record, please use the screenshot of your smart phone or tablet device.
■Display of stock value input and specification change value input
・Stock value input
Enter the stock specifications (front / rear sprocket / rear tire outer diameter (mm) / sensor gear tooth number) of the vehicle to which this product is to be installed.
・Change value input
After inputting the stock values for the vehicle in which this product is to be installed, tap "+" or "-" to change the front sprocket (drive sprocket), rear sprocket (drive sprocket), rear tire outer diameter (tire diameter) (mm), and sensor gear tooth number, and then make the settings.the number of sensor gear teeth.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
MODEL PAGE LINKS
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Customer Reviews
Reviews with image
Fits:HONDA MSX125SF , HONDA SUPER CUBC125 (JA48-1000001 and later), HONDA MONKEY125 (JB02-1000001 or later), HONDA MSX125 , HONDA GROM (JC75-1000001 or later)
Jan 27, 2022
Replacement of the old Takekawa speed sensor
New Custom Articles
