Rim Stripe 10M

When I repainted the wheel in black, I decided to put stripe on it I don't want to have fading and peeling, so I chose this product, and I was worried about using a 6″ wheel, but I decided to use a thicker 10″ wheel The result is just like the Image
For the pasting work, it is not difficult if you follow the Construction Manual I did not Also, I think it's better to cut off the backing and stick it on while peeling off the backing little by little Because I made it thicker, the positioning was easy, so I proceeded to Smooth

【What made you decide the purchase?】
At first we planned to purchase an infinite Rim sticker, but the price was twice as much as this product, so he was hesitant.

This product is about 3,700 yen for Motorcycle 1 Set for 1 Vehicle, affordable additions, plenty of Review has been posted, easy to grab the image of the product, and commentary animation of the installation method easy to understand on the product page was posted Also decided.

【How was it actually used?】
As shown in the image, the line just entered Rim, it became impressive Sporty at a stroke, it became cool. Large I'm satisfied..

However, although I bought a 10 mm Stripe this time, it was still not full of Rim width, but it was a different point than I imagined if it was far from far away.

【Was it difficult to install? (Hard parts case)】
Because we used Gauge (sold separately), the installation itself was very easy.
(In the case of * 10 mm Rim stripe, processing of Gauge is necessary.
For more info ↓ ↓ ↓ until Impre of Gauge
http : / / imp. webike. net / commu / article / 0282369 / )

The instruction manual was also very polite, so I was able to work with confidence.
Rather cleaning and degreasing of the prepared Rim took much longer.

【Please tell me the point of installation and hang (in the case of Hard parts)】
- For cleaning around the Rim and degreasing, the Instruction Manual "Car wash and degrease" Although it was written, although washing was troublesome, after cleaning carefully with the Car Wash sheet, we cleaned up with paper Dustcloth impregnated with Parts cleaner.

- If you are working outdoors, please be careful that Small stones and Small Nagomi will not stick to the sticker surface.
If you paste it as it is, it will float up from the bottom of the Sticker.

[Is there anything I was disappointed about?]
This is not Sticker but Gauge's fault, but I wanted to put the Sticker on the outside rather than inside the Rim.

【Hope for Manufacturer - Please let me know if you have any improvement points]
Is it even possible to have a thick Size?

【Have you compared items?】
Infinite Rim sticker

[Others] nothing special.

It is a little Large change to paste. It will take time to paste tightly. Well, it's just bad.
With Maintenace Stand, I think that you do not have to stop Motorcycle by pushing and stopping.
Although it is periodically done like WheelCleaning after pasting, it is pretty crisp but it does not appear to peel off. I think that durability is good. There are also various colors, so you can customize for yourself.

This time it is the third one to paste MDF's Rim stripe.

Simply remove the Rim with Parts cleaner and paste it.
There are things like dedicated rulers when sticking Rim stripe
As it is, it is always adhered to the center of Rim and it is quite beautiful if it is fitted only with the joint of Stripe neatly
It will be a circle.
I can make it in 30 minutes in the whole process and overall image will be better
I purchase it every time I change Motorcycle.

The red rim was attached to ZRX400 of red.
10 mm, it is quite thick, and attaches, or becomes and is conspicuous.although it only merely stuck since the appearance near
Tire changed a lot -- custom-made one -- in the bottom,
atmosphere comes out enough.
Above all, since it has already curved, it is quite easy to stick.If a little
neutral detergent is attached, adjustment of some resticking will hear.Since vehicles must be restlessly moved if it has neither vehicles without the
Center stand, nor a Racing stands, only a few is troublesome.