CS-H07 CS-550M Burglar Alarm Model Specific Kit

Vehicle specific anti-theft alarm.
Theft alarm for exclusive use with the Monkey 125, which is easy to set and release by operating the motorcycle ignition key without the need for a remote control, and easy to handle even for beginners.
All the parts you need for installation are ALL in ONE.
The length of the wiring has been adjusted for each model.
Wiring to the vehicle is coupler ON.
Includes instructions on where to install the main unit, siren and indicator.

■No remote control required!Set and release with your vehicle's key!
Simple operation by turning the key on and off.
You don't have to worry about carrying around the remote control or running out of batteries.

■High performance 3G sensor adopted!
The digital 3G sensor remembers the set state and reacts to suspicious movements.There are no false alarms!
The new version further reduces the false triggering caused by the vibration of the alarm set sound.

■Two-way warning / alarm system!
When the digital 3G sensor detects it, a warning tone will sound intermittently for 5 seconds.
In addition, if the digital 3G sensor continuously detects the alarm, it will generate a continuous alarm sound for up to 3 minutes.

■Re-memory function of digital 3G sensor
After the continuous alarm sound is stopped, the digital 3G sensor remembers the current status and keeps the alarm standby status, so when the sensor detects again, the warning sound and continuous alarm sound will be generated.

■LED indicator lamp included
You can check the standby status with the attached LED indicator lamp.
In addition, you can expect the effect of threatening and repelling by the flashing LED indicator lamp.
Conventional indicator lamps required drilling on the vehicle side, but the new version uses double-sided tape for easy installation.

■Remarkable power saving!
Current consumption in standby mode is only 0.9mA or less.
Power-saving type that is less than the self-discharge amount of the battery!

■No warning or alarm sound for one minute after setting!
The warning / alarm sound does not sound for one minute after setting the alarm, so it is convenient to avoid false alarms when you put the seat cover on after setting the alarm.
*However, the indicator light will respond.

■The compact design makes it easy to store in any location.
The compact design of the sensor body allows it to be stored in a small space.
*Some models may not be able to be installed.


[Facts on Theft!]
In 2013, more than 51,588 motorcycles were stolen annually.
This means that a vehicle is stolen every 10 minutes.
And about 90% of the damage has gone unresolved.
The stolen vehicles range from large motorcycles to mopeds.
Do you think that your bike is fine because it is a small moped?


○Is it a malfunction?Before people think so...
[Symptom] The alarm is activated immediately after setting the alarm standby
[Confirmation items]
The sensor of CS-550M is a special sensor called 3G sensor.
Unlike ordinary inclination sensors, this sensor is designed to memorize the posture (position information) of the vehicle when the alarm is set.
If the LED lamp flashes fast indicating an abnormality immediately after setting the alarm standby, and the alarm sounds one minute later, it means that the 3G sensor judged that there was a change from the location information stored when setting the alarm standby.
In this case, set the alarm standby while the vehicle is in the same position.
In particular, if the alarm standby is set while the suspension is depressed (e.g., while straddling a motorcycle), a change in the posture of the vehicle will cause the alarm to be activated when the suspension returns.
If the abstock behavior still occurs immediately after setting the alarm standby, fix the sensor body firmly to the vehicle body with cable tie.
Also, please install the sensor unit and the speaker at a distance.

[Symptom] I've got a dead battery.
[Confirmation items]
If the battery is turned off without setting the alarm standby, or if the battery is turned off for a short time during the alarm standby, the regulator of the sensor itself is damaged.
The two main causes of regulator damage are as follows.
1, When connecting the red and black cords of the sensor to the battery, the + and - cords were connected backwards even once.
2, Spikes generated on the vehicle side when the main key is turned OFF.(Instantaneous high voltage with a sharp waveform)
To check if the regulator is damaged, disconnect the red wire of the sensor unit from the + terminal of the battery without setting the alarm standby, connect an ammeter between the battery and the red wire of the sensor body, and measure the current.
If the current is around 65mA, it is abnormal.
The normal value is around 1mA.
If there is an abnormality, repair will be required.
"Please send the product, the warranty card, and a note describing the problem to the manufacturer.