Windshield

OEMScreen for BMWR1200R (Large type) However, I was not satisfied with the windproof effect and wanted to do something about it, but it was difficult to find a cheap product that would be effective in preventing wind. The design and price of WRS caught my eye and I ordered one.
When I received the actual product, I thought for a moment that it was only one size larger than the OEMScreen. However, when I actually installed it and drove the car, I could feel immediately that the windproofing effect had been dramatically improved. I was originally attracted by the design and price and ordered it with half a doubt about the performance, but I am Large satisfied with such excellent performance. The product is also very solid and I think the cost performance is perfect. I am really glad I chose this one.

Quantity with SupportFrame:I bought a Set, but it doesn't have Screw. Is this the Spec.
Even if NORMAL Screws are diverted, Screws will be insufficient.
Can you at least tell me the SCREW SIZE?

[How is it used?
"One-day Touring for a change of pace." sometimes "A change of pace, a ride on the town." 。

Was the one you received as per Image?
From Image Long, thick, and just a little Wide." It was.

Was the installation difficult?
Remove NORMAL." → Implanting Grommet." → Install this product." Only … but unique to BMWMotorcycle Torx bolt." Note that the product cannot be installed using ordinary tools alone, because it is installed with a

How was your experience with it?
above and below Approximately 15 centimeters." , in width About two centimeters. When Numerically sensitive?" but when combined with the NORMAL "Quite an Expansive Large." The wind suppression effect was also felt well.
"Sitting height over 1 meter." by yourself. 'Dwelling winds on the shoulders and neck (due to reduced cold)' I felt the That said. Direct winds to Helmet." What about the As for the Highways, etc." You will not know until you run the

[Included Parts:were they on?
Not even an Instruction Manual. It was. Well. I don't even recognize the product when I see it." Time is. "Motorcycle shop" Let's ask the

[Was there anything that disappointed you?
Driving on public roads in early spring in Hokkaido." The situation is not there at the moment.

Point and hang of installation
Normal screen's Grommet de-installation. is gentle and careful. In some cases, warm up with Dryeretc. "Corruption" Please be careful not to do so.

[Notes]
Self work." When doing the Tools for torx bolt" is required

[Opinions and requests to Manufacturer
"A cautionary tale." to Package, I felt that it would be good if it could be printed on Package, etc.
Product Quality, Visibility, Design." is good, so it seems to be a European product. Only those who know what they're doing should buy it." I'm a little disappointed in that.

I had been looking for a good price and a good looking product, and I couldn't find any examples on the web, but after looking at the products on webike many times, I got the impression that WRS was a good manufacturer, so I bought it.
The hole position is Exactly. Just remove the original and put this on.
The top part vibrates a little when running because of the large extension upward. I think it can't be helped because the fixed part is the same as that of NORMAL.
As shown in the photo, the ground seen through the Shield is partially distorted. When driving in town or in dense residential areas at low speeds, the Front area is a little distorted, so it feels a little uncomfortable, but you may get used to it.
I also drove a little on the highway on a windy day and felt safe without being agitated. （It is good that raindrops no longer hit the helmet shield.
I am wearing a Two La TEC hand guard and when I cut the handlebar full to the Right, it hits a little. In my opinion, it is a Level that does not bother me too much.

It's a little smaller overall than the OEMScreen, but I like it because it has excellent wind protection and rigidity if you put it up.
[Color] I think the smoke is just right, not too thick.