- The car was 10,000 km old and had been used for 10 years, but we decided it was time to replace it.Large is correct.The seal had lost its tension and the tip had become rounded.Piston shape is differe...Read More
- Purchased a used car that is 10 years old and has a little over 10,000 km,I thought it was time to replace it. I thought it was time to replace it.Parts is Piston and CupSeal is Quantity:Set andReturn...Read More
- I used it on a TriumphTIGER800 Rear master cylinder OH.First of all, the size of the OuterDust Boots is different when removing them, so be sure to remove them without damaging them so that they can b...Read More
- The size of the Circlip was different and the included items could not be used.I was going to use this Repair kit to make everything new, but alas.Circlip reused the previous ones.I think quality cont...Read More
- The BrakeTouch on my Z650 (Zapper) is getting worse, so I thought I would use the DAYTONANISSINMaster Cylinder OH and bought a repair kit.Replacement is not particularly difficult if you have Snap Rin...Read More
- I bought this for the Nissin OEM Master Cylinder Repair for my 98 GSF1200, and although it is not available for the Nissin OEM, I thought it was a bad idea since it is a Horizontal Type and the piston...Read More
- When Clutch fluid becomes cloudy and black, I think it is no problem to judge the deterioration of CylinderCup and Boots in Master Cylinder. As the relationship between Seal and Metal in Fork, Master ...Read More
- I used it to overhaul the front brake master cylinder of my TZr50R.The deciding factor in the purchaseThe Boots on the front brakes master cylinder had been cut off, so I thought I would just replace ...Read More
- I bought it for Overhaul of NISSIN Forged Radial master.I haven't used it yet, so I haven't evaluated its effectiveness.OEM Parts are separate with Packing included.Cylinder has Packing built into it....Read More
- I installed the old Nissin Radipon and Yamaha Brembo on my SRX600.However, after about 3km of test run, White smoke came from FCaliper!Rotor has locked up.I looked up the model number on the Internet ...Read More
- Purchased for the Master CylinderOverhaul.No complaints. A little BALI? I thought, but not so much that I couldn't assemble it.It's worth checking out, especially since the RubberBoots where Lever hit...Read More
- Fourteen years after I bought the car new, I used it for a MASTER Overhaul because the front brake fee ring had deteriorated.Overhaul of Caliper was also carried out at the same time, but it can be as...Read More
- For the overhaul of a 10 year old Brake master cylinder. Disassembled and cleaned plus replaced this Kit. Fittink is a ManufacturerRepair product so it's perfectly fine, I'd like to have the RubberBoo...Read More
- This product, I think it's just mine, but it's not a Nisshin product” So it's a DAYTONA” product.I checked the slip many times and it seems to be correct, Size was 5/8, so &rdquo I've done it, but it ...Read More
- I have a CRM250RR (before the AR), but the front brake was about 15 years ago I remembered to OH it once Because the front brake has become less and less efficient as expected recently (I can't JackKn...Read More
- Nisshin Horizontal Type Master Cylinder is used for about 8 years I was, sirI bought it for OHI was nervous to install the rubber on the Piston, but I was able to get the Piston Rubber has been instal...Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING