24.43 USD
(3,697 JPY)
4 (1 Reviews)
rating breakdown
5 Stars |
|
0 |
4 Stars |
|
1 |
3 Stars |
|
0 |
2 Stars |
|
0 |
1 Stars |
|
0 |
Very Good
After durabilityBasically it does not ride at night, but Tunnel part etc. I was concerned about the darkness and replaced it.
I purchased this if I aim for cheap cheap, was prepared to become a pillar (Lol) There is not Impre also ... (Lol)
Because it is this price with Relay, honestly I was disappointed but it was betrayed in a good way.
By the way it is 35 w 6000 k.
In our Motorcycle, we do not need an adapter, so we can do it as simple as Halogen bulb. There was also no defective product such as Wire on the light-emitting part in cheap comes up.. In addition, in the case of a common Rubber part, in my case purchase a Circle cutter at 100 ha and if you open a hole of about 20 mm in diameter, Valve also comes with the attached Rubber packing just the same. Waterproof processing is not required. And you can just attach it to Headlight cleanly.
Because Ballast is also a compact, the degree of freedom of installation seems high. I also get the impression that the fitting of Connector is also not particularly dissatisfied and it is good for the price.
There was slightly dirty Valve, but it is sufficiently acceptable range from the price.
Is it about several seconds until the light stabilizes? Although this neighborhood depends on the subjectivity, I do not feel dissatisfied. I think that it is rather early.
I'm on a SUBARU car, but the same etc. I received the impression of the earliest.
There is neither strange luminescence nor glare with beautiful coloring. I am relieved that CutLight also comes out very beautifully. CutLight fell about 2 cm from Halogen, but I am using it as it is. This neighborhood depends on Lens and Reflector, so it is not bad.
Brightness is quite inevitable, does not it compare with Halogen. Blue It is a beautiful white color with less taste.
In my opinion, I think that it is close to Level which can safely say OEM.
There may be a win and loss, but this quality is satisfying with this quality at the price of Halogen bulb as a little better eyes.
It is unnecessary if you can do DIY somewhat, but the instruction manual is in English. For the Wiring diagram, please translate it into Manufacturer HP (Please enter here for the Wiring diagram so please refer to it.
It's only durability after that (Lol)
By the way it is good to have Valve out on the road, the replaced Halogen bulb is put in the ValveCase attached to this product and put under Seat.
Most Viewed Reviews Of RISE CORPORATION HID Kit
Very Good
HIDFull kit[How is it used?
Halogen bulb of TDM850 is out, so I decided to replace it with HID.
Was the one you received as per Image?
I cancelled my order once and reordered, changed from H3 to H1.
Was the installation difficult?
The TDM850 was a Lamp replacement Large odd. The place is small and hard to get to.
How was your experience with it?
Large Variety Satisfaction
[Included Parts:were they on?
It was attached, but there was no Fixing Screw, so I fixed it with Double-sided Tape.
[Was there anything that disappointed you?
Installation/WiringManual is not good.
Other items that would be helpful
The Instruction Manual is difficult to understand.View Detail
Poor
Coil sound and color is strangeAt startup, there is a large Coil sound, and when repeating hi→low, there is a little sound Smaller works
I bought the 6000k and it's a green color with yellowish browns
It's so much darker than the 35w HID's I used to wear!
As it is 10 days after purchase, it seems to be unable to be returned and exchanged, so you have to be patient and use it It is not
A small, small drawing of a small Construction Manual in Japanese If you can build it by yourself, there will be no problem, but it is not kind to amateurs Yes
Wiring and coating do not seem to be bad, there was no tape peeling or defective terminals It's solid here
Rather than getting power from the Battery, you can connect to the Headlight without connecting it to the Battery Coil noise is a little better if you take it away from the wiring, just because it's better doesn't mean it doesn't sound But …
After a few minutes of running, it doesn't matter, and soon the Coil noise will gradually become small and stop
The cord for the terminals is a little short, and it's a little difficult to install on a Sports-type motorcycle I had a hard time with it This depends on the Motorcycle, so I don't blame you
It's a Minus with Coil sound and a Minus with Large sound
Minus in color, not so bright and even more minus
Very disappointing product, I can't help but say that I would not recommend it at all
The picture is of the OEM Light and HIDView Detail
Very Good
I'm fine with the priceI am sorry that the box of goods is solid but the contents are messed up without being in the bag.
I thought that it was unsatisfactory because the price was cheap, but for the time being, Motorcycle's Cowl was removed and Wiring was connected to start the engine ,,, BlueWhite light! Because light got on properly.
After that, decide the position of Ballast and Wiring, complete Cowl and complete.
Now I just installed, so I expect more brightness and durability.
Even without looking at the Instruction Manual, it was easy to install because there is no mistake in installation.View Detail
Excellent
Required enough at low price!GSX-R600 (K9) For Low beam (CenterProjector) Purchase. I ordered the installation to Motorcycle shop.
Ballast seems to be relatively easy to store because of the palm Size. Refreshing and storage was able to be stored in Space such as Meter back.
Low beam is the most used part so choose 6000 K safe. Even though it is lit with Single Body, it seems that Blue is slightly hanging at 6000 K, but basically the luminescent color is white.
Because we chose 15000 K HID for High beam, 6000 K is good Accent when pinched with Twin Light.
The amount of light is also sufficient, and you can feel the benefits of HID sufficiently in exchange from OEM's Halogen sphere. The reliability of Light at night is improved to the Large width, and the visibility from other cars seems to be considerably increased, so it seems that it will also play a role in Right direct accident measures.
Construction of Connectors was also OK, it was possible to install as it was. I do not feel Flicker etc, and it is a practical product enough for price. In addition, Hid Kit purchased from another trader had a lot of Small scratches on Ballast, there was somewhat dissatisfaction due to rust prevention etc, but Ballast attached to this Kit was pretty beautiful. HID can be purchased at this price is thankfully.View Detail
Average
Since spittle of the Burner was metal, this was decided on.
A spittle portion is also a Plastic and the thing attached before this has cracked unawares.
There is salivary thickness and it took pains over attachment again.
Since theSince spittle of the Burner was metal, this was decided on.
A spittle portion is also a Plastic and the thing attached before this has cracked unawares.
There is salivary thickness and it took pains over attachment again.
Since the former thing was un-switching on the light, the cheap thing was looked for at the auction site etc., but these goods were found and purchased by Webike.Although there was a cheap thing with the same metal spittle also at the
auction site, it is safer for there to have been no spread so much, when the mailing cost was included, and to purchase by Webike, if it is right. engine performance has no problem.Although the point of taking
Minus wiring not from a Battery but from vehicle body grounding was uneasy, there is no fault.
It is efficiently perfect.As it was in the photograph, a Ballast, a relay, etc. were installed in the Meter flesh side.
In fact, although he wanted to install in the car-body side, it was not able to do due to wiring length.
It is a size of the VOX in wiring between a Ballast and a Burner again to have become a problem.Are they
stable machine or something? Even if it states <(photograph right slippage, black box on Ballast.) br>small Ballast,The thing [ how ] does not specify such a bulky thing on the goods Page? <(isn't it a so-called Igniter Control Unit ?) br> In my case, although settled, depending on a vehicle type, it may become a problem.
This black box has uneasiness also in water proof again.Since a crevice will be easily made if
bottom lid is pulled, it is likely to be flooded if the upper and lower sides are mistaken at the time of installation.(It may be a satisfactory thing even if flooded)
If this stable machine and relay are not installed to the place which does not apply water if possible, it will seem that it is unsavory.I consider [ that it should improve publishing the photograph of the whole Set on a
* description-of-item Page etc., and ].
Although it was H3 Kit which I purchased, a part of Hi/Lo change wiring for H4 grades which is not used was contained.
Wiring is not difficult if you notice the point.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING