I attached it to RZ 350
Originally it was Swallow handle
What I was interested in is the height of the Handlebar
In Swallow 's posture was stooping
This person speaks somewhat
The position to sit a while ago
Because Handlebar feels a bit high
My arm feels a bit cramped
In case there is a feeling of incompatibility when using a little more
I plan to return to Swallow
Fits: YAMAHA XJR400R 01-07 RH02J *Processing to open switch hole required|*Side cap required (for 18mm diameter), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required
The Yamaha Y's Gear, which is slightly lower than the NORMAL and is attached with Option:The SR Moderate Screen now stands out. It seems to be compatible with Posh-Classical Rear Sets though the run is not yet done. It seems to be. I'm looking forward to the actual run.View Detail
Fits: YAMAHA XJR400R 01-07 RH02J *Processing to open switch hole required|*Side cap required (for 18mm diameter), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required
I decided to make KATANA Up Handlebar from low back pain etc, but I thought that I do not want to break the style of Separate handle and purchased it.
The diaphragm of OEMSeparate handle was about 40-Degrees, this product was the most restricted 32 degrees you looked for.
Top Bridge changed for NPROject's Up Handlebar and installed. The width fits within the range of the automobile inspection certificate with the Bar End attached, it moves up to 15 centimeters each, and the body goes up. It was enough to reduce the burden of the waist.
The load on the front wheels is reduced correspondingly, and the handlebar operation becomes unreasonable. I think that until you get used to, Cornering etc. I think that it is better to step forward by consciously.View Detail
Fits: YAMAHA XJR400R 01-07 RH02J *Processing to open switch hole required|*Side cap required (for 18mm diameter), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required
present vehicle,A state is behind brought [ that a Knee grip is not effective and ] at the time of accele
[Webike Monitor] by it being broad, and also hanging down to a Grip position and the angle being attached in case of the Handlebar attached with
present vehicle,A state is behind brought [ that a Knee grip is not effective and ] at the time of acceleration,When trying to stand on a Step to absorb unevenness of a road surface in a knee, a weight shift must be carried out because a Grip position passes before a hand,It purchases by having thought that it would exchange for the low thing which also has narrow width so that a Riding position may not suit me in any way and the load of it can be carried out to the Front side to a slight degree.Although it was uncomfortable at first when run after exchanging the
> Handle, it got used immediately and was a very good feel.
A riding posture turns into an inclined attitude lightly, an old problem is solved because especially the Grip position became low and the width of the Handle also became short 10 cm, and a run is also a Sporty.A Plating of the product itself is also beautiful and has no something to say.
It is although it is better if processing is however carried out stop shifting.View Detail
Fits: YAMAHA XJR400R 01-07 RH02J *Processing to open switch hole required|*Side cap required (for 18mm diameter), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required
the thing which has a few angle and which is low to a slight degree and hangs down by normal being high and hanging down since the angle is large -- it considered and made it this handle.
compared with the normal of
The SR400'07 model was equipped.
the thing which has a few angle and which is low to a slight degree and hangs down by normal being high and hanging down since the angle is large -- it considered and made it this handle.
compared with the normal of SR, it is somewhat low, and hangs down, and there is no angle -- almost -- a flat -- a few is extracted to the front.
Although it becomes a low and near position, a riding posture does not change mostly.
Height, an angle, and an iris diaphragm are exquisite and ride very easily.
Incidentally, since SR does not have the projection of positioning in a switch box and did not need to make a hole in the handle on the occasion of handle exchange, the point was easy.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING