OEM Product Interested in less expensive parts.

Bought his for my yamaha c3 aka vox aka giggle. Going to use it to clean up the rear lights. They fit and feel great, same if not better than oem.View Detail

Product was as in the picture with the smoke lens & the 2 red coloured bulbs. Voltage is similar so no worries about any mismatch. Screws are not provided so use back the original screws from the original tail light. Item arrived faster than expected! Super easy to install, just plug and play & the fitting is correct. End result is a cool smoke look to match my dark tone Steed body that no one else has!View Detail

ไฟท้ายสว่างมากๆครับมีหลอดไฟแถมมาให้ด้วยราคาอาจแพงกว่าkitakoนิดหน่อยแต่ก็ถือว่าคุ้มราคาดีครับ ^_^ (ภาษาไทยคงไม่ว่าอะไรนะครับ)LED tail light bulb Have bundled with a price may cost a little more but it is worth the price kitako good ^ (in Thailand would not mind it).View Detail

Vibration is an inherent part of single-cylinder, especially SmallEngine Displacement VolumeMotorcycles.
Tail lamp bulbs often burn out, but after many years of use, the tail lamp lens often develops cracks. It is a consumable item.
This product is OEM compatible.

good point
The position of the screw holes, etc. is also exact because it is an OEM compatible product.

Visibility is also satisfied.

Easy to obtain, inexpensive.

There are no drawbacks as it is a security PARTS.
In my experience, rain can penetrate through cracks in the tail lamp lens and cause problems with the electrical system, so it is a good idea to check this area.
The price is cheap, so I don't think you'll have a problem with Stock.
By the way, I always have about three Stocks (laughs).
You can ask a Motorcycle shop to do it for you, but if it is this replacement, it is more economical to do it yourself.View Detail

Tail light has been changed to that of LED
When the top of the image is Brake lit
At the bottom of the image Tail lit
is

Of course it is not only nighttime, but it also has sufficient visibility in the daytime
I wonder if this will go through a car inspection ...
I think that it depends on LED Tail being used

Some of the Smoked lenses from the company have a lower part for License Plate Light for License Plate Light, but in my case License Plate Light has OEM's as it is, so I made it Smoke Type entirely
Those who use the Type equipped with White LED for License Plate Light at the bottom with the outside LED tail are also lineuped so let's choose that one

However, I think that it is necessary to disconnect only a little bit there because it covers a little Rubber part for water intrusion prevention around the OEMTail lamp
Because it is a thin Rubber, I think that it is not troublesome to cut easily with Scissors and since there is no water invasion to that extent so ...
Fender Eliminator is a bit worried about the water that jumped up when traveling in heavy rain

Because it is a simple shape, there was nothing like being troubled at the time of installation
There is neither the position of the hole nor Gap ...
If it is Ninja it is the most troublesome to do it unless you change the Tail lens even if you exchange Tail cowl ...

The goods themselves were not in the Wound, etc. and in a good condition
As these sorts of cheap overseas products something like Wand sometimes got into it ...
If you use myself, if you use it Wound it will be good to go in, as it is polished with Compound lightly as it is (Lol)

As a precaution to wear when mounting, there is a possibility of cracking if you tighten it at once by changing the tail lamp and tightening with Screw
As I'm screwing in, I feel like I'm making threads with Tapping screw Screw
Once I screwed in half, I removed it once, breathed away the scraped waste once ...! I blown and blown and then tightened again

Red's Tail bulb is also included, but it's something like a bonus ...
It is wrapped in PetitPetit for storage in case of emergency
I used LED Tail was also a cheap item so I'd rather take it once in Touring, so ...
But SmokeTail and LED Tail are outstanding compatibility
Because the Blinker lens was also exchanged for Smoke before and after, the Rear view was also tightened and was satisfied with Large

It is quite cheap to exchange both, and both simultaneous exchanges are RecommendationView Detail

[How is it used?
I destroyed the return of the Brake switch that was originally attached to the YAMAHA/TZr50R during Restore.
Replaced with a new one. Compatible part number is 3MW-83980-00.

How was your experience with it?
It's working fine
Installation is also easy, as it is simply attached to the Master Cylinder.

How did it compare to other products?
It is very helpful that OEM parts are still available due to the lack of Other Brand Products.View Detail

Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail

?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail

I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail

Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail