67.69 USD
(10,244 JPY)
4 (29 Reviews)
Very Good
This is goodI can not compare because I do not have any other tools, but even if I did it by the procedure of the Instruction Manual as before for the first time I could change the chain without any problems. Incidentally it is Size of 520.
Price is not too high, I think that it tends to be broken immediately because it tends to be low-priced items I think that I am very good at Cost performance.
Reviews For Guard Lock Perfect Chain Tool From Other Webike User
Very Good
Friendly instruction manualI used to leave it to the store every time I changed the Chain, but now that I own more units, I decided to do it myself.
The Instruction Manual is very thorough and easy to understand, and the CrimpDataetc. for each ChainManufacturer is very helpful.
If you follow the Instruction Manual, even first-time users should be able to work without problems.View Detail
Average
Instruction Manual is helpfulI decided to try Chain cut & Crimp by myself since it costs 2 to 3 thousand yen at the store.
The Instruction Manual describes the work procedure in detail, so there are no problems if you follow the Instruction Manual.
I think it takes a bit of skill to determine the strength of the Crimp. I worked with the chain hanging in the air on the sprocket, but I should have put both the chain and the tools on the ground.View Detail
Excellent
It was easyI bought this to replace my Sprocket and Chain. I'm a guy who does a lot of my own maintenance, but this is my first Chain. This is the first time I've used Chain. The instructions are easy to understand and helpful. It was easy to install. I think it is better to think about the order of the Rose according to your vehicle in advance. At first I was not sure about the half price one, but it was the right choice. I thought that the tool for press fitting should be good.View Detail
Excellent
520-530Chain can be exchangedI had a chain exchanged at the shop before, but it caused trouble when I was out of town, and since then I've been exchanging chains myself.
This GUARD LOCK chain tool makes it relatively easy to DIY chain cut, plate press fit and pin head tabs.
I always use a grinder to grind the head down to flat before chain cutting. I don't know if I can cut well with the head as it is.
If you scrape down to Flat, you can Chain cut very easily and with light force. You don't need to be stupid to do it. =I recommend it.
Press-fitting the plate is easy as long as the proper positioning is done. The key is to carefully measure the plate width with a caliper. Once the width is measured, tighten the bolt as much as necessary, taking the bolt pitch into consideration.
Pin head tsubushi is uncomfortable at first because you don't know if you are doing it right. This is the work that needs to get used to. But if you proceed carefully while checking the dimensions of the important points with Caliper, you will not fail.
Thus, if you work one by one carefully, you can replace the Chain reliably even by DIY. I think it is enough performance as a tool for personal use. As for the durability, I have used it more than 5 times and I have no problem at all. (It might be good to have Spare for long PinBolt for Chain cut.
The chain is a very important safety component as well as the brake system. Understand the structure, prepare the necessary equipment such as Caliper, and do the DIY work responsibly.View Detail
Most Viewed Reviews Of Guard Lock Chains
Very Good
Friendly instruction manualI used to leave it to the store every time I changed the Chain, but now that I own more units, I decided to do it myself.
The Instruction Manual is very thorough and easy to understand, and the CrimpDataetc. for each ChainManufacturer is very helpful.
If you follow the Instruction Manual, even first-time users should be able to work without problems.View Detail
Average
Instruction Manual is helpfulI decided to try Chain cut & Crimp by myself since it costs 2 to 3 thousand yen at the store.
The Instruction Manual describes the work procedure in detail, so there are no problems if you follow the Instruction Manual.
I think it takes a bit of skill to determine the strength of the Crimp. I worked with the chain hanging in the air on the sprocket, but I should have put both the chain and the tools on the ground.View Detail
Excellent
It was easyI bought this to replace my Sprocket and Chain. I'm a guy who does a lot of my own maintenance, but this is my first Chain. This is the first time I've used Chain. The instructions are easy to understand and helpful. It was easy to install. I think it is better to think about the order of the Rose according to your vehicle in advance. At first I was not sure about the half price one, but it was the right choice. I thought that the tool for press fitting should be good.View Detail
Excellent
520-530Chain can be exchangedI had a chain exchanged at the shop before, but it caused trouble when I was out of town, and since then I've been exchanging chains myself.
This GUARD LOCK chain tool makes it relatively easy to DIY chain cut, plate press fit and pin head tabs.
I always use a grinder to grind the head down to flat before chain cutting. I don't know if I can cut well with the head as it is.
If you scrape down to Flat, you can Chain cut very easily and with light force. You don't need to be stupid to do it. =I recommend it.
Press-fitting the plate is easy as long as the proper positioning is done. The key is to carefully measure the plate width with a caliper. Once the width is measured, tighten the bolt as much as necessary, taking the bolt pitch into consideration.
Pin head tsubushi is uncomfortable at first because you don't know if you are doing it right. This is the work that needs to get used to. But if you proceed carefully while checking the dimensions of the important points with Caliper, you will not fail.
Thus, if you work one by one carefully, you can replace the Chain reliably even by DIY. I think it is enough performance as a tool for personal use. As for the durability, I have used it more than 5 times and I have no problem at all. (It might be good to have Spare for long PinBolt for Chain cut.
The chain is a very important safety component as well as the brake system. Understand the structure, prepare the necessary equipment such as Caliper, and do the DIY work responsibly.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING