* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
Sprocket, front - 1 rear + 1 acceleration Spec. Because we are doing, there is no need for limiter cut. (Lol) Also, I'd like to see an unnecessary shopping. - - - Defective item ??? Let's change it to front + 1 and try again Challenge ??? After all, it is the same as Large type SSMotorcycle...
This product come with good packaging . it also was easy to install by following the installation guild paper. when install it with cb1300 year 05 it need to stay in the form fastened with cable tie on a frame in the side case. Although the effect are able to feel from acceleration and the maximum high speed are getting better.View Detail
It attached to 08 MODEL CB1300SB.The purpose of use is cutting the Speed limiter at the time of a Circuit run. Since this product cuts only a Speed limiter and a Rev limiter is effective firmly, there are no worries about an Overrev.therefore, he is kind to an Engine -- it was the touch ?. 230 km/h was [ CB1300 of the FOR JAPAN MODEL ] actually a limit in the Circuit.It is not extended any more.Although it is attachment, it is not necessary to do large-scale work specially.Only with an attached description, it is attached enough. The black Cover of the Meter left is removed first.Since wiring is contained in the receptacle of a form like [ inside ] a bag, it is taken out in it and it is made to sink below a Coupler in it.Then, work is termination only by raising a Tank (the way is written on the instruction manual of a Motorcycle), making wiring of the left Side cover interrupt, and finally connecting long pink wiring to a Coupler along with a Main harness under a Tank at through and the last.Since pink wiring was fairly last-minute die length, it is necessary to make it the position in which it does not interfere when a wheel is turned.If it is a direction whose soldering will be possible since it does not become a problem if it excels 5 more cm, it can wire for a long time easily. Anyhow, attachment was easy and the end of work in about 30 minutes.Although that is right, when [ which may be upgraded depending on a vehicle type ] it is CB1300SB, it has not said so and only a Speed limiter is cut purely.View Detail
Perfectly fit to my bike zephyr x 400 cc.This POSH RED REV Super Limiter Cut come with Japanese manual and it connected at speedometer not directly to ecu.View Detail
This product come with good packaging . it also was easy to install by following the installation guild paper. when install it with cb1300 year 05 it need to stay in the form fastened with cable tie on a frame in the side case. Although the effect are able to feel from acceleration and the maximum high speed are getting better.View Detail
I used it but it broke down after less than a year, you can feel the power up. I bought it after it broke anyway, but if it breaks next time I won't buy it again. I need more durability!View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING