【What made you decide the purchase?】
Considering to introduce Suspension outside the company afterwards, unreliable short Rear inner fender mud Introduction considering strengthening prevention strengthening.
At the introduction page of GSX-S "Swingarm same as current R1000" Because there was a statement saying, I tried wearing Fender for GSX-R1000 by believing it.
Similar Fender is from each company, but I picked COERCE's which was moderately cheap and satisfied with which high Carbon fender Lineup was done.
【How was it actually used?】
Although there is no particular change in the running, when I saw the Tail under the rainy weather, the position where the dross is obviously changing is changing.
After that I wore the outside Suspension afterwards, but the suspension Body was covered somewhat with dust, but dross stains due to rainwater etc. did not adhere.
In OEM Fender, considering that the dirt was conspicuous considerably, the purpose of this time was satisfactorily achieved.
As for appearance as well, GSX-S1000F whose Volume is biased towards the front part, Volume increases backward due to the introduction of Long rear fender, it seems that Balance is well balanced well.
【Was it difficult to install? (Hard parts case)】
Since the Swingarm is common, the position of the Fender fixed Bolt was the same, but since the Bolt fixed position was inside the Swingarm and the tool was difficult to reach, it was necessary to remove Rear tire.
The accuracy of Fender itself is not so bad, and it was possible to fix Bolt without imposing excessive load on Fender when installing.
Also, because you can not use the gold fixation that fixes Brake hose with this Fender, you need to optimize the handling of Hose with Clip that adheres with double-sided tape.
[Is there anything I was disappointed about?]
Although it is not as expected as expected, I wanted Manufacturer Logo sticker to come with it.
【Hope for Manufacturer - Please let me know if you have any improvement points]
None.
【Have you compared items?】
A-teckRear Fender
マジカルレーシング Rear Fender
It is used for Ninja1000.
Since Magical racing takes a long time to deliver, I bought it anyway.
I was able to install it without any modification.
However, when I look at it from directly behind, it is not accurate or does not stick straight to the tire surface.
Well, I'm planning to replace it later, so I'm assuming it's not a problem.View Detail
The Ninja1000's OEM Rear Fender protects the rear suspension and They won't give it to me
There is a large hole in the ground
The cause is unknown, but the OHLINS developed an Oil leak a little over a year ago
If we don't plug this hole, will we see the same phenomenon again?
That's why I bought it
It's no longer available on We-Big, but you can buy it on Amazon They are ManufacturerMade-to-Order
Approximately 2 weeks delivery time
FittingNo problem, I was able to install it without any processing
However, there are some Wound on the edge of the cover, which is white in color It is especially noticeable at the edge of the Chain Cover
I don't care about it, so it's fine, but if it bothers you, I would recommend CarbonView Detail
19 years in use at Ninja 1000.
Every time I change Motorcycle, Rear Fender is exchanging.
Even on rainy days, Fender Eliminator + Rear Fender took off mud until Tail.
It was a Level that can be attached without precision processing.
I am wearing Nojima's Exhaust System, but it is considerably more than the general Hexagonal Wrench
If Head is not short Type Bolt will interfere with the Exhaust System and it will not loosen.
I worked with the Exhaust System installed, but I think that it is possible if tools are available to a certain extent.View Detail
Rear Fender of '10 type Z1000 has a cavity in the Small soak LINK part
Roll up mud and water just because the road is slightly wet
Suspension and sometimes to Helmet
(It is useless because it is a Fender Eliminator that attaches Helmet)
Because water and mud will adhere, we consider Fender of Other Company Product.
By selecting FRP as an inexpensive thing, select this item.
There is no distortion of Body and Screw hole gaps and it is completed in about an hour.
Since there is no cavity, there is no worry that Suspension will be directly contaminated.
After that, I will check if the mud splashes back to the back run.
However, only one ...
Handling Instruction Manual Why? "ZrX1200DAEG" Goods for
I was in.
Because there was Webike's invoice in the box
I think that it is inspected, but I want to have your attention once more.
View Detail
NORMAL's RFender is short and the Large hole is opened to escape the R SAS LINK.
On the rainy day the R suspension turns into muddy.
So I was looking for an external RFender, but I decided to make it COERCE which price was cheap and evaluation of Impression was good compared to Carbon.
Fitting was reasonable.
The two holes were slightly misaligned and fixed with File.
It is not a burden to do Large because it can be easily removed.
For those who are planning to install by yourself, it may be good to prepare a bar file just in case.
Although it was attached impression, it became considerably longer than NORMAL and the hole of the R suspension part also disappeared and I am satisfied with Large.
Design is also Cool.
I also wanted FFender to Carbon (Lol)View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING