11.89 USD
(1,800 JPY)
8.53~ USD
(1,291 JPY)
(28% OFF)
4 (5 Reviews)
Average
Part Detail<Size>
Bottle : Vertical 135 mm Horizontal 65 mm Depth 40 mm, Cap : Die-casting 40 mm Hose Insertion Length 20 mm Insertion diameter 12 mm, Drain : Material : Rubber 25 mm Hose Insertion Length 15 mm Insertion diameter 9 mm, Band mounting portion width 12 mm Depth 3 mm Center to center Pitch 65 mm
<Parts>
Bottle has rigidity, it does not feel dented in normal use. Drain rotates without being fixed. Cap is made by Die-casting and Smaller than Cap of Plastic bottle, the Bottle side is 22 mm, if there is a Bottle of the same diameter as this, it seems to be diversible.
<Overall rating>
I think that it is a reasonable price when considering the labor and parts cost for making this textured part with DIY. I regret that there is no Variation in the shape of Bottle.
Reviews For KIJIMA Oil Catch Tank From Other Webike User
Average
Between BreatherI used it when I attached the Breather kit to LEAD 110.
There is nothing special to mention. I can usually use it as an Oil catch tank, but I felt that the price is a bit expensive.
Large Kimono was slightly smelder than I imagined, but it was good as it is installed in a narrow Space.
Since capacity is visible, I made it as a product of plastics, but Aluminum may be better.View Detail
Most Viewed Reviews Of KIJIMA Oil / Gasoline Catch Tank
Excellent
ขวดน้ำสำรองขวดน้ำสำรอง เป็นขวดนำ้สำรองคุณภาพดี มาพร้อมกับสายยางที่ทนความร้อนได้ดีเหมาะสำหรับใส่กันรถแข่งและรถใช้งานได้อย่างดีเยี่ยมWater Bottle is a good quality bottle. Comes with a heat-resistant rubber cord.Suitable for racing and car use perfectly.(translated by Google Translator)View Detail
Excellent
Does the job!Affordable, perfect capacity and comes with long straps and plenty of hose...A lot of other kits come with tiny straps that are basically useless, these however were plenty long and are easy to remove too. Would buy again/10View Detail
Very Good
An old standby.Used for Gasoline & Radiator Catch Tank on NSR50.
(Engine is CR80, but w)
It is a product that has been around for a long time and I am used to using it.
I use them on my competition vehicles, so I buy them periodically due to falls, deterioration over time, etc.
I have not experienced any melting in Gasolineetc.
Might be affected by heat depending on where it is fixed?
I don't know because I've never put it on such a place, but it should be avoided lol.
Additional holes must be drilled if used for GasolineCatch.
Material:No problem as it is a Plastic product and easy to use.
On the other hand, only one hole is needed for RadiatorCatch, so the product is more universal as it is.
There are Round Type products from other companies, but I think Square Type is easier to use.
It's just a matter of ease of fixation.
It is unlikely that the product will sell in Large quantities for its intended use, but we hope that it will continue to be sold in the future.View Detail
Excellent
Gasoline leak preventionPurchase to prevent Gasoline leakage from carburetor - I installed it.
Magawa river VM 26 is attached to KSR 110, but there is a small amount of Gasoline leak even if you are on a regular ride.
In addition, a certain amount overflows from Carburetor even when it falls.
I do not want the Under Cowl becoming dirty, and it's kinda wasteful (Poverty) So I'm hiding in Under Cowl.
Size of container - The capacity is also exactly good, Hose and Valve, Tie Band for attachment is also attached, so there is a sense of affinity.
Although it overturned once after installation, since it was leaking about 20 cc at that time, I returned it to Tank as it was.View Detail
Very Good
Large is just right..Since Size is Small, it is better to have a high degree of freedom in the mounting position.
As it is attached to the car body, it is too conspicuous if it is exposed to Aluminum, so it is painted Black with tube Spray.
I think that this bank is sufficient for processing Blowby.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING