* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
If only VSeal's secondary air problem could be solved, the Power feeling, Torque, Response, The best carburetor in terms of fuel economy and everything, and surprisingly easy to set up, FCR It's also good because the body is not designed to be worn out like a And you can adjust the acceleration pump and Cut (Just pull out the shaft.) The difference between Yoshimurabrand and Mikuni is Just a Sticker?
OEMCarburetor to TMR replacement. There was a rumor that the setting was difficult to get out, the diameter of TMR36 was too large for 750, the driving was hurried, and it was not suitable for town driving, etc. There was also worry, but it can run with the setting at the time of shipment for the time being. At present, there is no problem at all in Idling - low speed - middle speed and town driving only by the adjustment of Pilot screw. The temperature is high, and it is a little dense, but I think that I will do it while enjoying the setting. Compared to the OEM Carburetor, the Response and Acceleration when you open the Axel is completely different. The Axel is also much lighter than the OEM.View Detail
I installed it on my Z1. It's a replacement for the CR33, but it's as if Motorcycle became something else. "Sharp. It will be It can be driven normally with a pontoon, but the Throttle is much lighter, and at first it will thump as if it were High Solo. I think you will be surprised if you open it with the same feeling as CR. But you will get used to it if you run a little. If you are not used to it, you can make it low slung to make it easier to operate. With the benefit of the Acceleration Pump, the feeling of acceleration is just amazing and makes you incredibly agile. Setting is easy ... . The carburetor body is designed not to wear out, so the body can be used for a long time ... . But if you are not sure, I think you should try it without thinking about the details. If you like to run, you won't regret installing it. It's a FlatValve, but it has a rounded shape, so it looks very good on older cars. In the case of Z1, Indicator needs to be replaced of course, but Throttle holder is OEM (Ripro) and could be installed without any problem. The Manual is also described in a very detailed and helpful way. One bad point is that Throttle Wire is hard to hang compared to CRetc. I think it will be a moderate struggle until you get used to it. However, once you install the engine and run the engine, you will be able to feel the difference.
I love the mattiness and look of the CR and will continue to enjoy it while changing it, but once you run with the TMR you will be amazed at its performance. Motorcycle (especially old cars) "Run. It's definitely a Carburetor that should be an option if you like the I was lucky enough to get it very cheap this time at WehBig's Sale...View Detail
I think that this price is attractive. Since it is already set up, unlike CR you can run even with an amateur even with an amateur. If it's not enough, you may want to set it up with Pro shop.View Detail
Very responsive system, which brings fun and fuel economy at the same time. I had this for my DR650SE suzuki. its amazing of course with all upgraded parts works very well and turn my average bike from a Cow to a Horse. I previously use mikuni pumper 42mm its same but fuel is not economy. The only problem is that the needle is hard to find, or no longer in production so try not to damage it. they should not stop production for this carb. its a good prioduct. I would Recommend if the parts still in production.View Detail
I use this carb on my bike 125cc. I.was very happy. Recently i have an issue. When i start my bike i try to throttle a little and my bike the carb, is choking. I can not accelarate smoothly. Only when the engine is hot enought the carb runs better. And also i cannot find needle set pilot jet and the smaller jet in the site to change it. The fuel mixing and air i try to adjust it but it didnt help much. Any suggestions will be very usefull cause i dont want to change the carb cause is to expensive. Also if u have needle set for the specific carb please let me know. Thanks.View Detail
"Plug and play" out of box - After some testing, I ended up with the already installed main jets #155. The "needle" -more precisely, the MJN-tube, had the best performance in the middle (Clip 3 from top) position (Also this setting from factory) . So basically I have only altered the slow fuel screw (Pilot screw) from 1 to 1.5 out, and accordingly the slow air jet from aprox 1 to somwhere between 1.75 to 2.00 turns out. I am also running power filter, and adaptors as well. Engine is 2mm overbore (1109 cc), 1:12 pistons, race-cams, dual valve-springs, zx11-D ignitor etc.The bike pulls like a train, and is very linear and responsive with this settings. Best carburators I have ever experienced :-) View Detail
[How is it used? I destroyed the return of the Brake switch that was originally attached to the YAMAHA/TZr50R during Restore. Replaced with a new one. Compatible part number is 3MW-83980-00.
How was your experience with it? It's working fine Installation is also easy, as it is simply attached to the Master Cylinder.
How did it compare to other products? It is very helpful that OEM parts are still available due to the lack of Other Brand Products.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
?
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING