This is the standard handlebar for circuit use I'm used to riding a motorcycle and I feel very comfortable with it
Installation and accuracy
It takes some care in handling the brake hose and wire The Axel was a little reluctant to return when locked, so I removed the Shroud of the Tank and put the Wire Adjusted the bend to be as gentle as possible and fixed the handling with amp;Tie Wrap As for the brake hose, I have a little bit too much left over for the OEM length (Hose length 735mm) I have replaced it with the One thing I noticed was the Switch box fixing hole, which is more of a potch than the OEMHandlebar The bite seemed a bit sweet There's nothing wrong with it in practical terms …
Shape and feel
Since the Handlebar has a slight aperture and droop angle, you can use it in combination with the Rear Sets You can get a natural stance when hanging on, from MOTARD to NAKED, which is more running oriented Is it a feeling of having become Position? When I cut the Handlebar which is indeed Large, the arm of the front side becomes cramped (laughs)
Cost performance
Not only is the actual selling price low, but it's also easy to fix if it bends in a fall
Fits: HONDA glom 13-15 JC61 (up to 1300000)(60mm down 95mm forward), HONDA glom 16-17 JC61 (1300001)(40mm down 65mm forward)
Installed on a Monkey 125, which leans forward a lot compared to the OEM.
The mounting holes are open for easy replacement, and the wires are large and sturdy as OEM, although there is some excess.View Detail
Fits: HONDA glom 13-15 JC61 (up to 1300000)(60mm down 95mm forward), HONDA glom 16-17 JC61 (1300001)(40mm down 65mm forward)
No drilling is required as it is specially designed for Grom.
Without the Handlebar Stopper, it will interfere with the Cowl.
Position is leaning forward and I'm happy with it.View Detail
Fits: HONDA glom 13-15 JC61 (up to 1300000)(60mm down 95mm forward), HONDA glom 16-17 JC61 (1300001)(40mm down 65mm forward)
This is for the Grom, so the Monkey 125 is not a compatible model, but I was able to install it without any problems.
However, because cables are inevitably too much, the handling and adjustment are a little cautious.
Because the Riding Position of the MONKEY125 is more Upright than the Grom, and it changes to the Low Handlebar for the Grom, it becomes a considerable forward lean.
It's not too tight to ride, but you might have a more natural posture if you wear the Rear Sets.View Detail
Fits: HONDA glom 13-15 JC61 (up to 1300000)(60mm down 95mm forward), HONDA glom 16-17 JC61 (1300001)(40mm down 65mm forward)
Pre-drilled holes for pumping
And for all the Machines we've seen so far.
Go ahead and use the black paint.
I'm feeling a little weak.
I chose Black again this time.
Handlebar position has been changed.
The position of the brake master has been changed.
Strain on the brake hose.
Mirror position also needs to be fine-tuned
Position is certainly good.
It is similar to the Image in Separate handle, but
The overall width will be wider than NORMAL.
From OEM position
Forward, Low, Wide
But if I wanted to, I could change it to
Forward, Low, Tight
If you have all three.
I personally think it's better than that.View Detail
Fits: HONDA glom 13-15 JC61 (up to 1300000)(60mm down 95mm forward), HONDA glom 16-17 JC61 (1300001)(40mm down 65mm forward)
I was worried about the manufacturer and the shape, etc., when I replaced it, but
I ended up going with this one because I thought it would be a classic and a sure thing
Large It was correct (・ω・) b
Originally, it was too vertical and Seat shape issues
My butt was too sore to ride for an hour
This is a natural forward leaning position and works well with the Rear Sets, which makes the weight It's dispersed and looks like it could be a long ride!
It's also easier to bend because it's easier to put weight on
As expected of a dedicated product, the interference to the tank at the time of the full stare that I was worried about is also a perfect shape and position No problem with the relationship
I didn't want to add a Stopper to change the angle of cut as much as possible
It was very good
The quality is normal, but just before the famous Manufacturer of terrible quality I was looking at Handlebar for, so it seemed pretty good
However, the paint seems to be weak, and it was scraped off immediately when I installed it
It's a very good product for Total and I'm quite happy with it! (・ω・) bView Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING