* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
No functional problems It's a hobby to change from OEM as it's not used very often
The front brake is compatible I installed it on a non-compliant rear brake for a test run, but the Fluid leaked The OEM has one hole on the Caliper side and this Parts has two The holes for air venting are also large Installation is easy because it is only replaceable, and the Cap is attached to the OEMParts as it is It is available
I've been sticking with the Tokico 6 pods. This time I adopted CaliperOverhaul and baked paint instead of OEM. I think it's a good corrosion protection. I've heard that some people use seal tape to prevent leaks, but I don't use seal tape because I have to loosen the Breeder repeatedly to keep the air out. I've had OEM jams in the past, but I'm not sure if it's because of the stainless steel. I'll have to wait and see.View Detail
The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel. Be sure to bleed the air and refill the fluid in the MASTER after replacement. The Bleeder Cap was made by Straight.View Detail
I replaced a 2006 K7 OEM BreederValve with a fluid blotch in the OEM BreederValve It is made of stainless steel and looks great I don't know if seal tape is necessary, but just in caseView Detail
I used it in a Tokico 6-pot, and since the Screw was with me, I figured I could use it! Brake fluid leaked and it was Large Please be careful There is no problem in the product View Detail
Because it rusts as soon as iron, Material : I purchased Stainless Steel. We are solidly making details, we are satisfied with Large change. I am happy that it's a bit cheaper.View Detail
I've been sticking with the Tokico 6 pods. This time I adopted CaliperOverhaul and baked paint instead of OEM. I think it's a good corrosion protection. I've heard that some people use seal tape to prevent leaks, but I don't use seal tape because I have to loosen the Breeder repeatedly to keep the air out. I've had OEM jams in the past, but I'm not sure if it's because of the stainless steel. I'll have to wait and see.View Detail
The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel. Be sure to bleed the air and refill the fluid in the MASTER after replacement. The Bleeder Cap was made by Straight.View Detail
ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. Don't forget to bleed the air and refill the fluid in the MASTER after replacement.View Detail
It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to be honest. I bought it more for corrosion protection, so I'm happy with it.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING