* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
[How is it used? I used it on a SEROW225 WE ForkOverhaul that had an oil leak. The oil seal is also made by NTB. The SEROW, which sometimes runs on forest roads and courses, was exposed to a large amount of sand and mud, and it seems that the inside of the Fork Boots was also contaminated. So I did a quick Overhaul.
How was your experience with it? It worked just as well as the OEM Dust Seal.
[Points to note] I think it's important to assemble it carefully and surely and to wash it well. I want to make it last longer, so it's nice to use Silicon grease and curing when assembling.View Detail
I'm planning on doing a lot of fork maintenance on my Honda Monkey. Little by little I collect consumables. I decided to try the anthers from NTB, since a year ago I replaced the anthers with original ones from Honda and they were cracked, I hope this will not happen here. In general, the quality of the products from this manufacturer is quite satisfactory, there are no comments.View Detail
[How is it used? I used it on a SEROW225 WE ForkOverhaul that had an oil leak. The oil seal is also made by NTB. The SEROW, which sometimes runs on forest roads and courses, was exposed to a large amount of sand and mud, and it seems that the inside of the Fork Boots was also contaminated. So I did a quick Overhaul.
How was your experience with it? It worked just as well as the OEM Dust Seal.
[Points to note] I think it's important to assemble it carefully and surely and to wash it well. I want to make it last longer, so it's nice to use Silicon grease and curing when assembling.View Detail
[How is it used? I used it for Front forkOverhaul of SR400 which I am restoring.
How was your experience with it? The Spec. is the same as OEM, though it is cheaper than OEM Parts. This kind of Seal will be a standard product. I use it without anxiety. I haven't run it yet, but it seems to do the job.
How did it compare to other products? No different from OEM.
[Points to note] To prevent Wound by curing with Vinyl when passing through Inner Tube. To put Silicon grease etc. in Rip. The basic Point of Fork decomposition is the same, such asView Detail
I bought this for the O/H of the Y's GearKYBFront fork on my MT-09. It was cheaper than the OEM Product and even better value for money with the Points.View Detail
There was no particular problem, but I found a crack in the Dust Seal, so I replaced it just in case. It acts like a lid to prevent Garbage from getting inside the Front fork. I bought this one because it was reasonably priced.
good point It's cheap.
The texture of Rubber is not so different from OEM.
After installing it, the accuracy of the parts is quite good.
A bad point The parts themselves are inexpensive, but the fork has to be roasted when replacing them. It's better to think of it as a Seal exchange as one of Fork's Overhaul rather than a Seal exchange.
Installation is not difficult, but rather tedious and time-consuming. However, if you replace the front fork (Overhaul), you will get the performance of a new front fork. If you are a do-it-yourselfer like me, refer to the service manual. Or you can ask a motorcycle shop to do it for you.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING