About quality and texture - Top quality. The syringe has a durable plastic housing that can be reused many times even when exposed to brake fluid.About the feeling of use - When removing and adding brake fluid from the master cylinder I like to minimise the chance of brake fluid being spilt on my paint work and this syringe and hose kit suits my needs perfectly.Products to buy together - The brake air bleed set from Daytona is perfect to purchase together with this syringe kit so all your brake bleed needs are covered.Difficulty of installation - The syringe kit is easy to assemble from the included items and even easier to use to extract and inject whatever fluid is needed.Cost performance and comparison with other products - With the inclusion of the hose and zip tie I find the syringe kit good value for a product that can be reused multiple times and comparing to the other kits available here on Webike, it's also the best value.About shipping and packaging - Sea freight is my preferred shipping option and usually arrives in Australia in 6 to 8 weeks from dispatch. Always well packaged to ensure parts arrive safety and are ready for use.Any concerns, cautions, or advice when purchasing - The included hose is only 15 cm long, so depending in your intended use it might also be worth adding some additional hose to your order.View Detail

Used several times so far. Ordered the item for bikes chain adjustments. Colour RED. Quality is fantastic. Fitment is perfect on sprocket. DIY alignment work is easy. Highly recommended item.View Detail

It is screwdriver magnetiser / demagnetiser. So the screwdriver can have magnet function ever the screwdriver have not the magnet function. It is good function when you need to screw something on. make it conveience and the screw will not easy to loss even in the small place. The colour is not light as the product page shown. it is more sharper. I like it color very much.View Detail

[How is it used?
This cylindrical Car Wash Brush is useful for washing narrow crevices when washing a car.

Was the one you received as per Image?
The total length was longer than I expected.
Considering my carrying and storage situation, another 5 cm shorter would have been perfect.

How was your experience with it?
I forget the Manufacturer, but the diameter of the Brush is thinner than the similar product I used to use, making it easier to insert the Brush into more detailed areas.
Brush's hair is quite firm.
I don't think anyone uses it, but it should not be used on Tanks, Screens, or other areas where fine scratches caused by car wash are a concern.
As the product name says "Engine brush", it is designed to be used on areas that do not get scratched or bothered by washing.
I use it in places that are difficult to wash with Sponge or regular Brush, such as the gap between engines, the gap between spokes, and the gap between exhaust pipes.
It was a pleasant realization that not only can hard-to-wash areas be cleaned, but it is also much more efficient than washing with Dustcloth, etc., so the time spent washing the car can be reduced.

As shown in the product image, the needle Gold of the core can also be bent gnarly.
The needle Gold in the core is quite hard, so it can be washed well even when bent.

[Points to note]
Rubber cap is attached to the tip of the Gold needle, which is the core of Brush.
In the unlikely event that this is not noticed coming off, it is likely to cause serious damage to the vehicle body.
Does it have a rubber cap?" and it is safer to look at it from time to time (a similar product I used in the past had a rubber cap that came off).

*Parts that cannot be used
It cannot be used for areas that must be bent internally, such as the inside of a Handlebar Pipe.
As mentioned above, the core needle Gold bends, but it is quite stiff. It does not bend flexibly to fit the other side while inserting it into a gap.View Detail

I think this product is an essential item for cowl removal. The resin also prevents the cowl from getting wound, and it is also useful for removing the interior of the car!View Detail

Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail

?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail

I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail

Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail

[How is it used?
Used to lick Screw loose.

Was the one you received as per Image?
As per Image.

How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.

It is also useful for DIY Screw removal.

[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail