* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I lowered my rear by 30mm and the front by 25, and I didn't need this even though I bought it. The standard kickstand put the bike on enough of a slant to make it stable. I am running fatter tyres than standard though so perhaps with standard tyres you may
I lowered my rear by 30mm and the front by 25, and I didn't need this even though I bought it. The standard kickstand put the bike on enough of a slant to make it stable. I am running fatter tyres than standard though so perhaps with standard tyres you may need this.
If a lowdown is carried out, it is necessary to change. Since it has finished by plating, there is also a high grade feeling. If time is formed from the field adjacent to a ground surface, plating will come off, but since it is seldom conspicuous, I think that it is satisfactory. Reinforcement also seems to be satisfactory.View Detail
If a lowdown is carried out, it is necessary to change. Since it has finished by plating, there is also a high grade feeling. If time is formed from the field adjacent to a ground surface, plating will come off, but since it is seldom conspicuous, I think that it is satisfactory. Reinforcement also seems to be satisfactory.View Detail
After attachment, when operation confirming was carried out, it was touch that there was also a portion which can completely start and scratch tension for a spring, and it took a crevice immediately. Therefore, also during the run, it drooped with bran lightly and was in the state which carries out a stand in the case of the left hander. When a manufacturer is contacted instantly, I hear that there is possibility of inferior goods and it has sent the elegance of exchange. When only springs were exchanged, it came to operate satisfactorily.View Detail
When rear suspension was exchanged for the thing of a 2-cm short, since the car body had become unstable, it exchanged here in the stand of normal. An excessive mind did not need to be used also when parking by favor. It is fairly troublesome, removing [ in W, although attached merely remove a muffler, or ] a side stands switch. When uneasy, I think that it is better whether to leave it to a motorcycle shop. The appearance of plating also matches bad that there is no sense of incongruity in W. What rusts easily is a difficulty. what is said -- * -- it is four.View Detail
It attaches with W650. Since it exchanged with Sas of the ohlins before, and the car body stood too much, it was likely to fall and I was fearful, they are short side stands this time. Exchange appearance also feels easy about this perfectly!!View Detail
Good seat, cleans up the W800/W650 nicely. Quality quite high. Seat feels firm and perhaps too firm for long rides but you get used to it. Your gf will be in your ear about how much her bum hurts. On my seat, the underside has holes where the rubber dampers are to be transferred across from your old seat as they are not supplied. These holes needed to be slightly drilled out. Overall recommended. View Detail
Looks great, works as it should. No complaints. I think WM Got it right when they designed this one. Everything else is too short or too long, and it still functions well as a water suppressant. View Detail
Overall quality is average. The frame itself is strong and sturdy, painting is of decent quality, it stands firm and square. A major problem however is all the threads need to be cleaned up as there is paint or zinc plating contamination causing the bolts to jam up. I encountered this with the main spindle bolts (2 black ones pictured), and the truing bracket which hangs in the middle. The nuts on this bracket were pretty nasty frankly...The truing bracket itself is quite crudely made and ends up not being perfectly square. The two bolts which point inwards are meant to be used to guide left/right truing, however mine aren\'t perfectly horizontal. This, along with the bracket being slightly off means accurate wheel truing can\'t be achieved. Not real happy with the quality. This tool is meant to be a precision instrument and it basically can\'t be used for accurate adjustment. Thought \Daytona\ were reputable manufacturers. View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING