TANAKA TRADING Steel Long Swingarm [10cm Long] (with Stabilizer)

Perfect fitment and quality craftsmanship coming from tanaka trading. I put 298km so far on this swingarm and still looking great.nice quality welds and shiny.View Detail

Good product at a glance.
It is a product that should not be bought by anyone who cares about the fine appearance of the product.

Paint is thick, but peels easily when Gold genus parts rub against it.
Some of the iron used in Large land rusts quickly.
It would be better to always have a Rust protection such as Spray or Touch up paint.
The weld marks are as clean as JAPAN products without any strange stubbers.

More eye-catching than that.
Is it for the chain line? Maybe, Stubby has a strange shape.
Large to the Left Side.
Distorted to the Left Side to the extent that it may interfere with the Side Stand.
It is so large that you may wonder if it is reused for Wide Stubby that was left over from other products.
I mean, you're recycling." It's so oddly shaped that it nods to the opinion that determines
Even images of stores other than webike use the oblique illusion to make them unrecognizable.
Since MONKEY itself is designed with very short swing arms, the pivot position is in an impossible position for a normal motorcycle. Therefore, if you use Long Swing Arm, the chain itself will sag when you ride due to the bad combination with Rear Suspension. If it is a Stubby to avoid the sagging, it may be acceptable, but the appearance is very bad.
I'm sure Stubby won't interfere with Chain if we leave this much space open, right?" (grin)" It is so crooked that one can almost hear the voice of

Stubby is not suitable for the low &long ride height that Japanese people like.
If the Swing Arm is almost horizontal at 8Inch, it'll scrape on the sidewalk steps at the entrance to the store.
It was about 2-3 inches off the ground visually when adjusted with Jack without suspension.

I was expecting a Swing Arm with Stubby that had a sports taste.
The product that arrived was a Swing Arm with a perverted Stubby, which is a straight line of colorful things......orz

The strength itself is steel + Stubby reinforcement, so it's pretty pushy.
When putting the hubs in, if they went in at a slight angle, it was quite difficult to fix.
It seems that there is no strange rustling even if it is loaded with luggage and carried on its back and ridden over 100 km overall on mountain passes and elevated bumps.


Because I feel comfortable seeing images of people working together on social networking sites, etc.
Once assembled, it's a discreet object.
If you're like me, you're looking for a "Quantity:Pair (for Left and Right) For those who prefer "symmetry and firm symmetry", this is a very uncomfortable part!

However

"Look." Than "real" (i.e. not "actual") I can recommend it to those who takeView Detail

Tanaka Shokai TANAKAAluminum Long Swingarm [4cm Long] has arrived and I'd like to give you a quick in-play of how it feels to use it

It was a product I was curious about and purchased
Honestly, I have no complaints about the quality/price of the product and it's working normally
However, the product was not outstandingly good in any way

I bought the product and I don't feel like I'm losing money
As far as shopping goes, I felt like it wasn't a loss

It is a product worth the Gold amountView Detail

It says that the hub installation width is the same as OEM, but when I tried to put it on, there was a lot of gap I tightened it up anxiously, and the Center fit as it was
Before that, I tried to put the swing arm shaft through, but the part that goes through the shaft is too large Stop-lamp switch UnitBracket must be processed to fit, and final assembly The gap between the left crankcase and the left crankcase cover is very close to the moving parts when It was Well, because both of them are aluminum, if it interferes, it should be a good thing that it can be removed No
Also, the Brake Rod is attached by L-shaped hooks and pinned in place
I have to check it from time to time to make sure it's safe
After all, it's made in ChinaView Detail

This 10-inch aluminum wheel is a great upgrade for Dax and Chaly builds using the 3-spoke hub setup. The machining is smooth and consistent, and the overall finish looks sharp straight out of the box. Fitment is spot-on with the 3-spoke hub, no spacing issues or adjustments needed. Once mounted, the wheel runs true and gives the bike a clean, refreshed look. It’s a simple upgrade that makes a noticeable difference in both appearance and ride quality.A solid, well-made wheel that suits restorations, custom builds, or anyone wanting a better-looking alternative to stock.The tubes feel thick and well made, they come with the bolts to bolt the 2 rims togehter but not the rim to hub bolts, you will need to use the stock bolts for this. These do NOT fit the 3 spoke hubs with a single piece steel outter rimView Detail

This MINIMOTO headlight is a great replacement for aging square eye chaly headlights that might have chome peeling or a cracked lens. The lens is crystal clear, and the reflector has a sharp, clean finish that gives a bright and more focused beam compared to worn OEM parts.Fitment is spot-on it sits perfectly in the original housing with no extra gaps or wobble. The overall look stays true to the classic Chaly design, just much fresher and cleaner. It’s one of those small upgrades that really lifts the front end of the bike and improves night visibility at the same time.A reliable, well-made replacement part that restores both function and appearance on any Chaly build.View Detail

This MINIMOTO tail lamp and bracket set is a clean upgrade for any Chaly build. The bracket is nicely made with good rigidity, and the lamp itself has that classic Chaly look without feeling cheap. Wiring is straightforward, and everything lines up with the factory mounting points, so installation is quick with no modification needed.The light output is bright and clear, making it a noticeable improvement over old, faded OEM units. Once fitted, it sits straight and tidy, giving the rear end a much fresher appearance.If you’re restoring a Chaly or building something a bit custom, this set is a reliable, well-fitting replacement that lifts the overall finish of the bike.View Detail

This Z2-style side cover emblem is a great little detail piece for anyone building a Kawasaki-themed mini or restoring a Z2 Mini replica. The moulding is sharp, the lettering is crisp, and the chrome finish looks clean without any rough spots or casting marks.It mounts securely and sits flat on the cover, giving the bike that proper vintage Kawasaki look. It’s a subtle part, but it really helps tie the whole side profile together, if you’re going for that classic Z2 aesthetic on a Z50.View Detail

This Sportster-style tank from Tanaka Trading is a standout piece if you’re going for a custom bobber or mini-Sportster look on a Monkey. The shape is spot-on, classic Sportster lines scaled perfectly to suit the small frame and it really changes the overall stance of the bike.The finish is clean out of the box, and the welds are tidy for a tank in this price range. Fitment is straightforward, and once mounted it sits nicely without awkward gaps or weird angles. If you want your Monkey build to lean more toward the Harley/Sportster aesthetic while still keeping everything compact and proportional, this tank is a great starting point and gives the bike a totally different presence.Tank comes with tap and capView Detail