?
As per manufacturer, sprocket material able to last above 10000km & more. Pricing was reasonable for good material used.Have not install yet, will see how it goes & revert later on.
Fits: HONDA BENLY 90S 96-01, HONDA Ape50 Type-D 08-13, HONDA BENLY 50S 96-07, HONDA Ape100 Type-D 08-13, HONDA BENLY CL50 97-01
With the stock 2018 Honda Monkey 125cc engine the motorcycle would struggle with large hills in fourth gear. After some research it was suggested to either go down one tooth on the front sprocket or go up two teeth on the rear sprocket. With the front sprocket being cheaper and easier to change I went that option and the improvement was well worth it as now the motorcycle can pull up those large hills in fourth gear where in the past I would have had to shift back to third gear. The fit and finish of the product is as go as OEM do it matched up to the OEM rear sprocket and chain well. My only issue now is my speedo is no longer accurate.View Detail
Fits: HONDA BENLY 90S 96-01, HONDA Ape50 Type-D 08-13, HONDA BENLY 50S 96-07, HONDA Ape100 Type-D 08-13, HONDA BENLY CL50 97-01
[How is it used?
I installed these on my 2015 Super Cub 110.
OEM is 14T, so I installed 15T which is one up.
Was the one you received as per Image?
As per Image
Compared to the OEM, it was about a size larger, and there was quite a difference in appearance.
Was the installation difficult?
It was my first time to replace it, but I was able to do it on my own without any problems.
Instruction Manualetc. is not particularly, but I think that even a beginner can do it quickly because it only removes and puts on the thing originally installed.
How was your experience with it?
I felt a very large effect in the driving of CUB110.
Since the speed is higher at a lower rpm than before, the load on the Engine is also reduced.
The slow start was not as bad as I had heard and the increased top speed made the bike very easy to ride.
It's been a long time since I've done a Custom and I'm glad I did.
[Included Parts:were they on?
Everything that was supposed to come with it was there.
[Was there anything that disappointed you?
I would like to make a recommendation to CUB riders.View Detail
Fits: HONDA BENLY 90S 96-01, HONDA Ape50 Type-D 08-13, HONDA BENLY 50S 96-07, HONDA Ape100 Type-D 08-13, HONDA BENLY CL50 97-01
Changed front and rear Sprockets at the same time to replace the Chain I installed a MADE IN SUNSTAR Sprocket on a different motorcycle before I thought I'd make in sunstar for the CUB as well … but The Rear was not commercialized and it was Front
Because there is no hole for weight reduction, the KITACO's Sprocket that I had installed until now It weighs 88g compared to 77g and is +0.2mm thicker at 6mm It was a finished product, but the engraving was pointing at an angle
Unlike LargeEngine Displacement Volume vehicles Sprocket stuck, although Sprocket is not fixed at high Torque Remove the bolt while stepping on the rear brake After replacement, tighten the bolts with 10Nm to finish the job
It's just a shame that we couldn't have it all in MADE IN SUNSTAR before and after, because the finish of the product was so good It wasView Detail
Fits: HONDA BENLY 90S 96-01, HONDA Ape50 Type-D 08-13, HONDA BENLY 50S 96-07, HONDA Ape100 Type-D 08-13, HONDA BENLY CL50 97-01
I bought it because I have used it on a large motorcycle, so I thought that durability is not a problem My 15T is an STD, but when I installed the AXIS lab tube, the torque was lost underneath As a result, I thought I had no choice but to cover by the number of Front, and selected 14T (-1 Ding) Naturally, the Piece number of Chain is also changed? I thought it was 98Piece (STD), but I heard it was 97.5Piece, so I stayed with it I went
As for the speed, MONKEY-STD, the speed is 4km from the GPS speed, and 3km from the 1 Ding! Together, it is -7km, but in the test run, it was -9km & plusmn; 1km So, I decided to subtract 10km from Meter without putting the speed sensor kit, and to use it as a test run I don't look at Speedometer very often!View Detail
Fits: HONDA BENLY 90S 96-01, HONDA Ape50 Type-D 08-13, HONDA BENLY 50S 96-07, HONDA Ape100 Type-D 08-13, HONDA BENLY CL50 97-01
Bore up the GROM and changed the power to Front16T Buy to
There are two types of screw holes for fixing (one wide and one narrow), but in the case of GROM OEM, the wide screw hole is used Use
Sprocket came with a fixed Plate, so the original Plate that came with it was a work in progress It interfered with the Shaft at the stage of installation and was not able to be tightened by Socket I noticed
I could tighten it up with Spanner, but I'd have to recover the original OEMPlate from the Garbage bag Installation
Since the camshaft was also changed, it is a little difficult to use the low RPMs, but even in 4th gear, it can go up to 100 km/h It came out without stress
Meter error was originally a canny HappyMeter, as far as the GPS on my phone is concerned However, I feel like I've become a slight HappyMeter
Front 16T and Rear 34T at 80km on GPS, about 78km
View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING