?
Not a lot you can say about handlebars. They look good and seem to be of a high quality, time will tell. However there are a few points worth mentioning. There is a manufacturers sticker where the grip goes, and not making it an easy to remove sticker meant I took about 20 minutes soaking and rubbing the area to remove it.Also the standard bars have a location hole for the left and right switch cluster to stop them rotating. These bars do not so you either drill a hole and hope to get it in the correct position, or remove the locating pin from the switch cluster.
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 vtec III*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm)
这个车把比原厂的车把窄了不少，另外，原厂的那个车把真得好重，这个则要轻很多。然后这个车把他不像原厂的车把有往回弯的那样，所以整个骑行的姿势会往前稍稍前倾一些，而原来的姿势是直直的坐着，相比较而言我还是更喜欢这个姿势，腰部会更舒服一些。车把短了有一些别的问题，national cycle的这个挡风适配不如原来的车把好了。----------------------------------------------The handlebar is narrower than a lot of the original handlebar, in addition, that the original handlebar really well heavy, this will have a lot of light. Then the handlebar He does not have that back the original handlebar bend, the entire riding posture will move forward slightly forward for some, but the original posture is sitting straight, comparatively speaking I prefer this position, the waist will be more comfortable. There are some other short handlebar problems, national cycle of the wind adapted better to the original handlebar good.Powered by Google TranslatorView Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 vtec III*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm)
Качественный, красивый руль. Установил его вместо оригинального. Очень удобный для меня по сравнению с оригинальным. Удобнее посадка, легче и комфортней управлять байком. Минусы немного шире оригинала, тяжелее. Очень понравился руль. Рекомендую.Quality, beautiful steering wheel. Installed it instead of the original. Very convenient for me compared to the original. Comfortable fit, easier and more comfortable to drive a bike. Cons a little wider than the original, heavier. Loved the steering wheel. Recommend.translated by Google TranslatorView Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 vtec III*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm)
I replaced Handlebar to immeChain.
The height of the handlebar is now much lower.
It's so much easier to ride.View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 vtec III*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm)
I'm putting it on my SR
I was looking for something a little lower and wider than NORMAL and decided on these
I was a little concerned about the width, so I cut the ends by 1cm on each end and rode it
I've been using it for a long time and I love the textureView Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING