I bought this engine guard for it's low price, however it is too soft at the connection part, this may protect your bike only if it is still and it will bend.
Fits: HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250M 17-20
We're going to be touring, so just in case, we're going to have to take a stand and fall protection, etc. Purchase Installation
It is easy installation with the U-shaped bolt fixing both at the top and bottom, but the scratch prevention TapeOthers of Frame
You will need to protect it with film, etc
It would be nice if you could install it in the vehicle's Bolt
I couldn't really see the delicacy in the pictureView Detail
Fits: HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250M 17-20
Purchased on Amazon on 04/20/2019
When I installed it, if you turn off the Handlebar, which is a large handlebar, you will see the Front It's grazed by Fender
In fact, the Fender is soft and bent, so it won't do any real harm, but it's not a pleasant one! Hey
I think the U-shaped fixation to the frame and the error of the body weld is the reason for the large size I think, but I would have liked to see a few more to considerView Detail
Fits: HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250M 17-20
I purchased the Renewal version on Amazon on 19/04/2019
I installed it by myself, but when I cut the Handlebar which is Large, it is Front Fender I'll rub it in
The Fender flexes softly, so it doesn't do any real harm, but it's not a pleasant one
I know it's hard to find the position because it's fixed with a U-shape, and there may be an error in the shape of the frame weld I'd like to see a little more consideration for body errorView Detail
Fits: HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally Lowered 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250 Rally 17-20, HONDA CRF250M 17-20
Installed in CRF250Rally LD
This time I was prepared to buy it as a human pillar
This is because I was looking at the reviews of the previous part number and was quite anxious to install it
As it turns out, there will always be interference somewhere
Lower Attachment and Under Guard
Side Fairing and Engine GuardPipe
Engine Guard Upper Bracket and Pipe Weld and Front Fender
The above three points are the main areas of interference
The instructions say to fix it in a position where it doesn't touch the Fairing or Fender, but It's a difficult task
The most dangerous point of contact with the Fender is the contact point with the Fender, and even if you avoid it, you'll still have 1-2mm of clearance It was the best I could do
The Fender is soft and doesn't feel like it's going to catch when you hit it, but in some cases, the The Handlebar could be taken, which could lead to an accident
Also, if you tighten it firmly so that it doesn't move, the bracket will become soft and deformed It is
It was bent and the paint cracked
Small Electrician? Despite the fact that I tightened it with the Ratchet on the Spanner, it was deformed, so I had to tighten it with the Spanner I stopped
So it cannot be installed with Firmly and moves slightly
As you can see from the above installation conditions, it may become undrivable due to deformation and Gap when it falls over It is not
Especially since there is a possibility of collision with a Fender, it's better to check it before you start the car I think
Side Fairing and Pipe's overhang is also pretty close, depending on the road conditions ahead Fairing is more likely to make contact
According to the instructions, though, it's supposed to be for standing mishaps and minor falls
You should expect to be ruined in the event of a fall
If you want to ride with the intention of falling down, we recommend you to use the overseas type which can be installed more firmly It is
One good thing is that the Pipe diameter is the general handlebar diameter, so you can use it for fog lamps and photographic equipment I think it's good for such a use because it can be used as an attachment bar for I think
It may be a good or bad cosmetic experience for each person
I'm going to use it as an insurance + Attachment Bar for my personal use
The photo is of Fender's ClearanceView Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING