Installed on a GLADIUS 650650. replaced the OEMHandlebar as it was too Up and tiring.
The Sauce angle will be good and the Position will be just right.
Of course, there is no hole, so you can borrow an electric drill at a home-centre and make a hole by yourself.
Drill is a good buy for 6mm.
- Instock
20.55 USD (3,129 JPY) 21.01 USD Save 2%
Delivery Information
In Stock, Ships within 24 hours.
Estimated arrival date around
FITMENT
-
CB400SF
-98 NC31 *Processing of switch hole required|* Required side cap (for 18mm ID)
-
CB400SF
08-21 NC42 VTEC Revo *Requires switch hole drilling|*Requires side cap (for inner diameter 18mm)
-
CB1300SUPER BOLDOR
10-12 *Processing of switch holes required|* Required side cap (for 18mm ID)
-
CB400SS
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
See all
HONDA
-
XJR1300
07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID)
-
XJR400R
01-07 RH02J *Processing to open switch hole required|*Side cap required (for 18mm diameter)
-
TW225E
00- (Disc Brake Car) *Processing of switch hole is required
-
XJR1300
00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID)
See all
YAMAHA
-
GRASS TRACKER Big Boy
09-12 (FI car)*You can use stock side caps.
-
GRASS TRACKER
09-12 09-12(FI cars)*Side caps can be used with the stock ones.
-
GRASS TRACKER Big Boy
-08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
-
GSX400
05-07 GK7CA *Processing of the switch hole is required|* You can use the normal side cap.
See all
SUZUKI
-
BALIUS
91-94 *Processing of switch hole required|* Required side cap (for 18mm diameter)
-
BALIUS2
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
ZEPHYR750 RS
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
ZEPHYRX
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
See all
KAWASAKI
-
Universal
Product detail
Handlebar color: Chrome plated
[Handlebar specification]
Handle: Black steel / Outer diameter φ22.2mm / Inner diameter φ18mm
・Stock cables and hoses can be installed on as is
[handlebar size]
Total height: 75mm
Full width: 690mm
Effective width of holder installation part: 130mm
Pullback size: 145mm
Insertion angle: 30 degrees
Forward leaning angle: 70 degrees
*
*Handlebar clamps (holder or post) in the photo are not included in the product.
*Sizing shown is for a horizontal position.
*Images may contain other colorings and types..
For the list of optional parts such as cables
7/8 Inch Road Model Normal Handle Size Chart
7/8 Inch Scooter / American Model Normal Handlebar Size Chart
1 Inch American Model Normal Handle Size Chart
.
Made in Japan.Prototype, installation confirmation and mass production are all under in-house management.These handlebars are made with a great deal of care and attention to detail, including careful selection of materials, several types of polishing, engraving of part numbers, high-precision bending and welding, and high-quality surface treatment, based on technology and know-how cultivated over many years in Osaka in Japan.STKM13A steel material with excellent tensile strength is used.Cleared by JMCA safety standard value.Triple nickel and chrome plating (3 layers of nickel and chrome) finish with thick film and excellent durability and corrosion resistance.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.