- Installed on GB250 CLUBMAN.Since it could not be attached as is, the pin side was shaved 5mm using a grinder. If the amount of shaving is wrong, the angle will be wrong.The footpeg rubber is not remov...Read More
- I used it on my XG250 TRICKER quite some time ago, but recently I have been storing it in my Parts storage, forgetting how easy it is to use Tatsumi's Change cover.The W800 OEM Change Pedal had a hard...Read More
- Fits:
- KAWASAKI Varios 2 91-08
- KAWASAKI barios 91-08
- KAWASAKI Ninja 250R 08-09
- KAWASAKI Zephyr X 96-08
- KAWASAKI Zephyr 750RS 91-06
- ...and more.
I put it on my A7. The rubber of the original footpeg was hard and slippery, and the gold part was badly corroded and dirty, so I decided to replace it with Other Brand Product.It looks similar to the...Read More - Fits:
- KAWASAKI Varios 2 91-08
- KAWASAKI barios 91-08
- KAWASAKI Ninja 250R 08-09
- KAWASAKI Zephyr X 96-08
- KAWASAKI Zephyr 750RS 91-06
- ...and more.
I was able to install it without any problems. It was fully compatible with the GPZ900R-A7's Normal step. The spring that came with it was Exactly, but the pin was too long, so I used the Normal sprin...Read More - I replaced the soft, airy footrest of the Yamaha MT-01 with this SolidRubber one.However, as shown in the note, when the Pin is Crimp, it is necessary to remove and replace it by shaving off, and the ...Read More
- Fits:
- HONDA
It was impossible to install on CB250R. I have to throw it away. It was a waste of money. Please be careful everyone.Read More - Fits:
- KAWASAKI Ninja 250SL 15
- KAWASAKI Ninja 250 13
- KAWASAKI
- KAWASAKI
- KAWASAKI
- ...and more.
Position will vary slightly.It's attached diagonally up and back.I thought it would be cooler if the bars were straight out wGood product for the price.I tried it out and I think the quality of the pr...Read More - Fits:
- KAWASAKI Ninja 250SL 15
- KAWASAKI Ninja 250 13
- KAWASAKI
- KAWASAKI
- KAWASAKI
- ...and more.
I bought it for the ninja1000SX 2020.The OEM with Rubber does not have to transmit vibration.I bought it because it is too heavy and the bottom of Boots and the Rubber catches too much on each other.T...Read More - Fits:
- YAMAHA YZF-R6 99-08
- YAMAHA YZF-R25 15
- YAMAHA YZF-R1 98-03
- YAMAHA XJR400R 93-08
- YAMAHA XJR400 93-08
- ...and more.
I installed it on a 2016 MT25. The installation itself can be done without any problems, but it is much longer than the OEM footpegs and harder to ride. In addition, the installation part protrudes ou...Read More - Fits:
- KAWASAKI Ninja 250SL 15
- KAWASAKI Ninja 250 13
- KAWASAKI
- KAWASAKI
- KAWASAKI
- ...and more.
As a person who wears racing boots even when touring, I'm not a fan ofPedal is far from subtle in both Z250SL OEM footpegs.I've been wanting to do this before, just for a minute.I found this one and s...Read More - Fits:
- YAMAHA YZF-R6 99-08
- YAMAHA YZF-R25 15
- YAMAHA YZF-R1 98-03
- YAMAHA XJR400R 93-08
- YAMAHA XJR400 93-08
- ...and more.
I used it on my THRUXTON 900.Triumph is made in the United Kingdom on a United Kingdom man's Height Base, and for further Rear SetsKnee grip is very strict and the knee is too low, and the knee is too...Read More - The Madmax foot pedal cover is an awesome addition to a cool bike! I get more comments about it than I expected. It is a littl bit heavy, but it fits great and gives more area on the brake pedal for y...Read More
- Fits:
- SUZUKI Bandit 1250S 07-08
- SUZUKI Bandit 1250 07-08
- SUZUKI Bandit 1200S 06
- SUZUKI Bandit 1200 06
- SUZUKI GSX1400 01-08
- ...and more.
The footpegs are solidly built, look good and feel great to ride with. They allow for slightly more lean angle due to the lack of sliders underneath the pegs. However, one of the pegs comes loose over...Read More - Fits:
- HONDA PCX125 10-21
- HONDA PCX125 11-21
- HONDA PCX150 (KF12)
Very nice products.Royal Rất thích nó, nhưng vận chuyển về Việt Nam quá cao hơn giá trị sản phẩm. Các bạn có thể hỗ trợ chuyễn giao dịch không? Very Luigi special products on the elevator thật tiếc .....Read More - 【What made you decide the purchase?】 There is only this in the old car.【How was it actually used?】 Large kimono is also Just fit.【Was it difficult to install? (Hard parts case)】 There is a need to rem...Read More
- Fits:
- HONDA PCX150 (KF18) *Not available for KF12
- HONDA PCX125 (JF56) *Not available for JF28
As it will be sent in a flat state, you must bend yourself.It is difficult to draw a curve. Sure enough, a gap has been created.Just peel off the OEM's Rubber, just install the Bolt and Screw.Alth...Read More - It is normal as a product. There is yzf - r25 in conformity, but mt - 25 (Yzf - r25 as well) You can not attach a ponto. OEM Radial ball and Spring will not enter. I added it by expanding the diameter...Read More
- Fits:
- HONDA glom (MSX125)
OHLINS is bad Copy goods.There are many defect reports reported on this siteThe most severe thing is that the core in the middle is broken and it is extremely dangerous* The image is already p for peo...Read More - Fits:
- KAWASAKI Ninja 250SL 15
- KAWASAKI Ninja 250 13
- KAWASAKI
- KAWASAKI
- KAWASAKI
- ...and more.
Excellent for COSPA. At this price you can not buy at other Manufacturer. The appearance changes at once. Instructions are not included, but installation is easy as it is the OEM street.Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING