- Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
I've been sticking with the Tokico 6 pods. This time I adopted CaliperOverhaul and baked paint instead of OEM. I think it's a good corrosion protection. I've heard that some people use seal tape to pr...Read More - Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel.Be sure to bleed the air and refill the fluid in the MASTER after replacement.Th...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. ...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to b...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
I bought this as a replacement from OEMvery high (Lol) Expensive for nothing. (Lol)The color of 64Titanium material of the same size is SilverTitanium and about 1000 yen.Quantity Stainless this time:2...Read More - Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
I replaced a 2006 K7 OEM BreederValve with a fluid blotch in the OEM BreederValveIt is made of stainless steel and looks greatI don't know if seal tape is necessary, but just in caseRead More - Fits:
- その他
i installed it on my bremboRCSRadial masterit's shorter in length than the brembo OEM, but the only thing shorter is the top half, so it's not a problem for useThe 10mm Wrench is useful because you ca...Read More - Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
No functional problemsIt's a hobby to change from OEM as it's not used very oftenThe front brake is compatibleI installed it on a non-compliant rear brake for a test run, but the Fluid leakedThe OEM h...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
CYGNUSxInitial Model (SE12J), if it's the same Caliper model, this The product fitsI couldn't find anything that looked like a match and it was a no-go, but it was OK with no problemsIt is recommended...Read More - Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
I used it in a Tokico 6-pot, and since the Screw was with me, I figured I could use it! Brake fluid leaked and it was Large Please be careful There is no problem in the productRead More - I had you report with photos with deterioration in the previous review in half a year.I bought it again this time and used it for a year, but it has been improved without any early deterioration as be...Read More
- I purchased it because there was no Cap in the vehicle I bought in second handIt is a cheap item and you can exchange without any hesitationBecause I lost while I do not know, I would like to keep the...Read More
- 【What made you decide the purchase?】 price【How was it actually used?】 very good.【Was it difficult to install? (Hard parts case)】 it's simple.【Please tell me the point of installation and hang (in ...Read More
- Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
The shape of the tip is slightly different from OEM. I feel a sense of incompatibility when I put on Rubber cap.Seal tape winds in the reverse direction, not in the tightening direction.Noticing that ...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
Noticing that Brake fluid seeped out of Caliper's Air breederRust was amazing as I removed it. Indeed when I thought this was dangerous, I found this productReplaced. As I wrote that the installat...Read More - Because it is worrying about water and dust, if not, it is purchase for the second time, butThe first crack has occurred in one year, I think that this time as wellIt is a little bit more durable than...Read More
- I felt that the material of Rubber itself is different from the OEM Parts Number. There is a feeling of durability that seems to be in the Impre of the other person. If it is used provisionally, there...Read More
- Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
We exchanged from OEM Parts Number during Maintenance of Commuter Scooter.I checked the number of Air breeder, OEM Parts Number for Nisshin caliper and purchased it.As described in the manual, I rolle...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
We will also exchange Air breeder according to Brake fluid exchange.I confirmed ProductNo in the Parts List and confirmed its compatibility with this product and ordered it.Roll Seal tape and install....Read More - Fits:
- その他
Previously, there was no tool to match when brembo's MASTER, Caliper air bleeding tried, and there was a memory to go buy. By changing to Breeder here, it will be 10 mm Box so you can make it with...Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING