HONDA MSX125 (GROM) Engine Parts

very good performance, it pull hard around 9000 rpm . very good quality product. takegawa 5 speed transmission is recommended . hopefully takegawa will make 181cc DOHC engine for honda monkey 1...

Excellent piece of kit. Always can be in the right rpm range unlike stock transmission. First gear is a little tall, would rather it be shorter but it is still ok. Makes the bike faster and shift...

Wanted to use this piece but it seems less oil travels over oil temperature sensor and the temperature is reading very high even though the true temperature is normal.

Wanted maximum horsepower so I added this cam to my build and although it does not wheelie with throttle only, it does pull hard to 12,000 rpm

Went in without issue. Revs to 12,000 rpm without failure. Make sure flywheel mating surface is clean and dry without oil before you torque to spec.

Since my 2018 Honda Monkey 125cc does not have traditional oil filter and runs the oil spinner system I wanted to add a little extra protection for the engine. The Special Parts Takegawa magnetic...

After lots and lots of research on camshafts for the Honda Monkey 125cc I decided to go with the Special Parts Takegawa N-20 or Sports Camshaft. This is the first camshaft I have tried on the 125...

[How is it used? For intake and exhaust custom

Was the one you received as per Image? Street Image

Was the installation difficult? Easy installation.

How was your experience ...

Nicely made bolt with a grub screw and slots to hold the temperature probe that comes with the takegawa HUD replacement. Highly recommended.

Another supporting mod for the BBK upgrade is the 4th bearing support to keep the engine in good health with that added power from the 143cc N-20 kit. Beautifully made item from Special Parts Tak...

Looks really nice and refresh compare to the original timing hole cap set. It's so easy to change makes my Honda Monkey more livelier.

KITACO:Throttle kit is a necessity if you want to install NEOBore Up Kit. The kit also includes a bracket for oil cooler installation. KITACO:Big Throttle Kit is available in two versions, one fo...

While replacing the lightweight oil filter
Because it is cheaper than the ones of Mukawa, I bought it without thinking anything, but because I divert the OEM Parts, I installed it is a bit of ...

I forced myself to install it on a MONKEY125 Exhaust System Up Type The result is not immediately apparent, so I have to rate it as 3 Installation is very easy if you follow the instruction manua...

Sense and self-satisfied dress-up parts, with parts that have nothing to do with driving performance Maybe I should have gone with the Black one? Maybe after a few years the colors will degenerat...

msx125인데 순정 제품이 워낙 약하게 얇게 만들어져서 튜닝하려고 구매했습니다 다른 회사 제품도 있지만 키타코 제품이 더 좋아보이고 튼튼해 보여서 키타코 제품으로 골랐습니다 직접 교체할수가 없어서 아직 장착은 안했는데 물건만 봐도 순정보다는 튼튼해 보이네요 Genuine product is very weak though it i...

I changed it to 1.6 times of OEM because of the installation of SStageBore Up Kit The fuel control is controlled by FIcon 2 I don't have the A/F ratio meter now, so I don't know the actual A/F ra...

Here's a little point that I changed while installing the Takekawa's 5 speed Mission This time it's Quantity:Pair (for Left and Right) In addition to the Crank Case Cover, the same is applied to ...

I recon the Kitaco Cross Gear Set is the best and easiest way to improve the GROMs 4 speed transmission. Using a 1:1 4th gear in the GROM requires a change of final drive sprockets to complement ...

Installation and quality
Because it was purchased with Couplet-onKit, Wiring has been using the Coupler as per the instruction manual Once connected, it was fine (Don't worry, if you make a mi...

[How is it used? I bought this Touring Main because I replaced the Exhaust System.

Was the one you received as per Image? On Image.
It's nice to have a little Red in the house.

W...

It has been replaced before, but since the Odometer has exceeded 70,000km, it is part of the overall parts replacement process.
I don't know the symptoms of the air filter, but I assumed that ...

[How is it used?

Was the one you received as per Image? Street Image

Was the installation difficult? It's easy

How was your experience with it? Blowing up is better now.
<...

The difference between the OEM Flywheel and the EnduranceLightweight Fly Wheel is the cutting process of the StarterClutch attachment part to reduce the weight! ! In order to replace the flywheel...

Until now, I've been using the OPMID product, which is almost a "standard" in the GROM world
It was functional enough, but I couldn't stand the poor visibility during the day and decided to re...

The products of major CustomManufacturers such as SP Takekawa and KITACO and Compare and contrast the exclusive design of the car models to see if you like the installation location and design Th...

I installed it in SUPER CUBJA10 while looking at the Instruction Manual Wiring was done I almost made a mistake because the power supply is always Red, the ON position is Black and Earth is Green...

I put it on to counteract the emulsification of the late MODEL
I have also put on the OHLINS Rear shock, but the Shock's Reserver The tank was set up to be attached to the same place as this o...

The ENDURANCE (GROM) Oil Cooler Mounting Kit for 4V Head add indicates this mount is product specific. I could not get this product to fit my Endurance type 4v cylinder head satisfactorily. If yo...

Hola llego muy rápido, ya está instalado, pensaba que se iba a notar más, hay una diferencia de peso con respecto al original de 152 gramos. Pero no está mal por el precio que tiene. Vendedor...