88cc after the Bore up, and since it was feeling, it exchanged here.
Naturally the slide was lost.Since it was cheap, it is very much satisfied with
mailing cost lump.
[Webike Monitor] The pure Clutch slid on
88cc after the Bore up, and since it was feeling, it exchanged here.
Naturally the slide was lost.Since it was cheap, it is very much satisfied with
mailing cost lump.
Fits: HONDA Monkey Baja 93 [Frame No.]Z50J-2100001 or later, HONDA Monkey Baja 92 [Frame No.] Z50J-2000001 to 2006661, HONDA Monkey Baja 91 [Frame No.] Z50J-1700001 to 1900805, HONDA MONKEY 69 [Frame No.]Z50A-169786 or later, HONDA MONKEY R 1987 87 [Frame No.]AB22-1000017 and later
On my goods was received, but due to the prices that you and I are taxed too high, hope the trip following the transaction, you can write off the bill-ThanksView Detail
Fits: HONDA Monkey Baja 93 [Frame No.]Z50J-2100001 or later, HONDA Monkey Baja 92 [Frame No.] Z50J-2000001 to 2006661, HONDA Monkey Baja 91 [Frame No.] Z50J-1700001 to 1900805, HONDA MONKEY 69 [Frame No.]Z50A-169786 or later, HONDA MONKEY R 1987 87 [Frame No.]AB22-1000017 and later
* Since I forgot to check Impression CONST test, it is a re-post.. I'm sorry if I was covered.
【What made you decide the purchase?】 Price and function
【How was it actually used?】 While being strengthened, Lever's lightness is also light.
【Was it difficult to install? (Hard parts case)】 It closes every time for the hardness of pure Normal Thread Screw of Centrifuge Filter cover.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Anyway, arrange the tools carefully.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】 -
[Is there anything I was disappointed about?] There is none.
【Hope for Manufacturer - Please let me know if there are any improvement points; I would like Screw of Filter cover to be the hex head..
【Have you compared items?】 Takegawa and SHIFT UP Reinforced Clutch
[Others]
Purchase with webike. In relation to making CUB 90 over 110 cc, Manual clutchization against the increasing Power
I bought it for.
I went to Smooth without much difficulty in installation, but I wrote that the sound comes out with impression
As I saw it, I made a sufficient oil bath in Friction disk in advance.
Initially it was a little dragged and dragged, slipping at the time of KICK came out, but it quickly dissolved and calmed down.
Although Lever's pull is light, it seems that it is being properly strengthened, and there is no feeling of sliding and it connects spatially at all.
After one year of use I am making Mukawa centrifuge for the pursuit of CUB likeness, but this Clutch of DAYTONA is medium
It was easy to use.
It's a bit cheaper compared to others, it's not heavy, and it's recommended because it's not a problem quality.
View Detail
Fits: HONDA Monkey Baja 93 [Frame No.]Z50J-2100001 or later, HONDA Monkey Baja 92 [Frame No.] Z50J-2000001 to 2006661, HONDA Monkey Baja 91 [Frame No.] Z50J-1700001 to 1900805, HONDA MONKEY 69 [Frame No.]Z50A-169786 or later, HONDA MONKEY R 1987 87 [Frame No.]AB22-1000017 and later
【What made you decide the purchase?】 Price and function
【How was it actually used?】 While being strengthened, Lever's lightness is also light.
【Was it difficult to install? (Hard parts case)】 It closes every time for the hardness of pure Normal Thread Screw of Centrifuge Filter cover.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Anyway, arrange the tools carefully.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】 -
[Is there anything I was disappointed about?] There is none.
【Hope for Manufacturer - Please let me know if there are any improvement points; I would like Screw of Filter cover to be the hex head..
【Have you compared items?】 Takegawa and SHIFT UP Reinforced Clutch
[Others]
Purchase with webike. In relation to making CUB 90 over 110 cc, Manual clutchization against the increasing Power
I bought it for.
I went to Smooth without much difficulty in installation, but I wrote that the sound comes out with impression
As I saw it, I made a sufficient oil bath in Friction disk in advance.
Initially it was a little dragged and dragged, slipping at the time of KICK came out, but it quickly dissolved and calmed down.
Although Lever's pull is light, it seems that it is being properly strengthened, and there is no feeling of sliding and it connects spatially at all.
After one year of use I am making Mukawa centrifuge for the pursuit of CUB likeness, but this Clutch of DAYTONA is medium
It was easy to use.
It's a bit cheaper compared to others, it's not heavy, and it's recommended because it's not a problem quality.
View Detail
Fits: HONDA Monkey Baja 93 [Frame No.]Z50J-2100001 or later, HONDA Monkey Baja 92 [Frame No.] Z50J-2000001 to 2006661, HONDA Monkey Baja 91 [Frame No.] Z50J-1700001 to 1900805, HONDA MONKEY 69 [Frame No.]Z50A-169786 or later, HONDA MONKEY R 1987 87 [Frame No.]AB22-1000017 and later
I attached it along with Bore up. I think that the ratio of GEAR changes as well. I thought that fitting with Sprocket was troublesome, I aimed for two birds with one stone. The function of Clutch itself seems to be connected to sputteringView Detail
Fits: HONDA Monkey Baja 93 [Frame No.]Z50J-2100001 or later, HONDA Monkey Baja 92 [Frame No.] Z50J-2000001 to 2006661, HONDA Monkey Baja 91 [Frame No.] Z50J-1700001 to 1900805, HONDA MONKEY 69 [Frame No.]Z50A-169786 or later, HONDA MONKEY R 1987 87 [Frame No.]AB22-1000017 and later
When I tried built-in test run, when I grip Clutch lever I heard a rattling sound. Is it a misplacement in the early stage? Is there a mistake in installation? Also, there was no play of Clutch that was there before (I can not cut when making play) Is it such a thing? Clutch is also well broken and connected with no problem for running.
View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING